kernel/git/stable/linux.git/drivers/iio/accel, branch linux-4.7.y

iio: accel: kxsd9: Fix scaling bug

2016-09-24T08:09:31+00:00

commit 307fe9dd11ae44d4f8881ee449a7cbac36e1f5de upstream. All the scaling of the KXSD9 involves multiplication with a fraction number < 1. However the scaling value returned from IIO_INFO_SCALE was unpredictable as only the micros of the value was assigned, and not the integer part, resulting in scaling like this: $cat in_accel_scale -1057462640.011978 Fix this by assigning zero to the integer part. Tested-by: Jonathan Cameron Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: accel: bmc150: reset chip at init time

2016-09-24T08:09:30+00:00

commit 1c500840934a138bd6b13556c210516e9301fbee upstream. In at least one known setup, the chip comes up in a state where reading the chip ID returns garbage unless it's been reset, due to noise on the wires during system boot. All supported chips have the same reset method, and based on the datasheets they all need 1.3 or 1.8ms to recover after reset. So, do the conservative thing here and always reset the chip. Signed-off-by: Olof Johansson Reviewed-by: Srinivas Pandruvada Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: accel: kxsd9: Fix raw read return

2016-09-24T08:09:29+00:00

commit 7ac61a062f3147dc23e3f12b9dfe7c4dd35f9cb8 upstream. Any readings from the raw interface of the KXSD9 driver will return an empty string, because it does not return IIO_VAL_INT but rather some random value from the accelerometer to the caller. Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: accel: kxsd9: fix the usage of spi_w8r8()

2016-06-26T16:32:19+00:00

These two spi_w8r8() calls return a value with is used by the code following the error check. The dubious use was caused by a cleanup patch. Fixes: d34dbee8ac8e ("staging:iio:accel:kxsd9 cleanup and conversion to iio_chan_spec.") Signed-off-by: Linus Walleij Cc: Signed-off-by: Jonathan Cameron

iio: st_sensors: switch to a threaded interrupt

2016-05-29T19:21:41+00:00

commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded ("iio: st_sensors: verify interrupt event to status") caused a regression when reading ST sensors from a HRTimer trigger rather than the intrinsic interrupts: the HRTimer may trigger faster than the sensor provides new values, and as the check against new values available as a cause of the interrupt trigger was done in the poll function, this would bail out of the HRTimer interrupt with IRQ_NONE. So clearly we need to only check the new values available from the proper interrupt handler and not from the poll function, which should rather just read the raw values from the registers, put them into the buffer and be happy. To achieve this: switch the ST Sensors over to using a true threaded interrupt handler. In the interrupt thread, check if new values are available, else yield to the (potential) next device on the same interrupt line to check the registers. If the interrupt was ours, proceed to poll the values. Instead of relying on iio_trigger_generic_data_rdy_poll() as a top half to wake up the thread that polls the sensor for new data, have the thread call iio_trigger_poll_chained() after determining that is is the proper source of the interrupt. This is modelled on drivers/iio/accel/mma8452.c which is already using a properly threaded interrupt handler. In order to get the same precision in timestamps as previously, where samples would be timestamped in the poll function pf->timestamp when calling iio_trigger_generic_data_rdy_poll() we introduce a local timestamp in the sensor data, set it in the top half (fastpath) of the interrupt handler and provide that to the core when calling iio_push_to_buffers_with_timestamp(). Additionally: if the active scanmask is not set for the sensor no IRQs should be enabled and we need to bail out with IRQ_NONE. This can happen if spurious IRQs fire when installing the threaded interrupt handler. Tested with hard interrupt triggers on LIS331DL, then also tested with hrtimers on the same sensor by creating a 75Hz HRTimer and using it to poll the sensor. Signed-off-by: Linus Walleij Cc: Giuseppe Barba Cc: Denis Ciocca Reported-by: Crestez Dan Leonard Tested-by: Crestez Dan Leonard Tested-by: Jonathan Cameron Fixes: 97865fe41322 ("iio: st_sensors: verify interrupt event to status") Signed-off-by: Jonathan Cameron

Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

2016-04-26T22:07:23+00:00

Jonathan writes: 2nd set of new device support, features and cleanup for IIO in the 4.7 cycle. Bit of a bumper set for new drivers but plenty of other stuff here as well! New device support * ad5592R ADC/DAC - new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips. * Aosong am2315 relative humidity - new driver with triggered buffer support in follow up patch. * bmi160 imu - new driver * bmp280 - bmp180 support - note there is support in the misc/bmp085 driver. Intent is to remove that driver long term. * invensense mpu6050 - cleanup leading to explicit support of mpu9150 with a good few cleanups along the way. * Hope RF hp03 pressure and temperature sensor. - new driver * maxim DS1803 potentiometer - new driver * maxim max44000 light and proximity sensor - new driver built in a series of steps to support pretty much everything. * ROHM BH1780 light sensor - new driver. There is an existing driver in misc that this is pretty much intended to replace. The discussion on whether to support the non standard interface of that driver is some way is continuing. * st-gyro - lsm9ds0-gyro. The accel/magn side of this will take a while longer as extensions to the st library are needed for cases where two types of sensor share a single i2c address. * ti-adc081c - support the adc101c and adc121c * Vishay VEML6070 UV sensor - new driver. New features * core - devm_ APIs for channel_get and channel_get_all. The first user of these is the generic ADC based thermal driver. As it is going through the thermal tree these will be picked up as a patch to that next cycle as that is how the author preferred to do it. - mounting matrix support. This new core support allows devices to provide to userspace (typically from the device tree) allowing compensation for how the sensor is mounted on the device. First examples are on UAVs but it has a more mundane use on typical phone where the chip may be on the front or the back of the circuit board and soldered at any angle. Includes support for this ABI in ak8975 (which has an older interface, now deprecated) and mpu6050. * tools - add a -a option to enable all available channels in generic_buffer sample. Makes it somewhat easier to use. * adis library and drivers - support manual self test flag clearing. This has technically been broken for a very long time - result is an offset on readings as the applied field is on all the time. * ak8975 - triggered buffer support * bmc150 - spi support (including splitting the driver into core and i2c parts) * bmp280 - oversampling support. * dht11 - improved logging - useful to debug timing issues on this quirky device. * st-sensors - read each channel invidivually as not all support the optimization of reading in bulk. This is technically a fix, but will need to be backported if desired. - support open drain and shared interrupts. * ti-adc081c - triggered buffer support. Cleanups * inkern - white space fix. * ad7606 - use the iio_device_claim_direct_mode call rather than open coding equiv. * ad799x - white space fix. * ad9523 - unsigned -> unsigned int * apds9660 - brace location tidying up. - silence an uninitialized variable warning. * ak8975 - else and brace on same line fix. * at91_adc - white space fixes. * bmc150 - use regmap stored copy of the device pointer rather than having an additional copy. * bmg160 - use regmap stored copy of the device pointer rather than having an additional copy. * hid-sensors - white space fixes. * mcp3422 - white space fix. * mma7455 - use regmap to retrieve the device struct rather than carrying another copy in the private data. * ms_sensors - white space fix. * mxs-lradc - move current bindings out of staging - some will be shortly deprecated but the reality is that we have device trees out there using them so they will need to be supported for some time. They accidentally got left behind when the driver graduated from staging. - white space cleanup. - set INPUT_PROP_DIRECT. - move ts config into a better function. - move the STMP reset out of the ADC init. * vf610_adc - case label indenting fix.

iio: accel: bmc150: use regmap to retrieve struct device

2016-04-19T18:58:17+00:00

Driver includes struct regmap and struct device in its global data. Remove the struct device and use regmap API to retrieve device info. Patch created using Coccinelle plus manual edits. Signed-off-by: Alison Schofield Reviewed-by: Irina Tirdea Reviewed-by: Srinivas Pandruvada Signed-off-by: Jonathan Cameron

iio: st_sensors: support open drain mode

2016-04-19T18:58:13+00:00

Some types of ST Sensors can be connected to the same IRQ line as other peripherals using open drain. Add a device tree binding and a sensor data property to flip the right bit in the interrupt control register to enable open drain mode on the INT line. If the line is set to be open drain, also tag on IRQF_SHARED to the IRQ flags when requesting the interrupt, as the whole point of using open drain interrupt lines is to share them with more than one peripheral (wire-or). Cc: devicetree@vger.kernel.org Cc: Giuseppe Barba Cc: Denis Ciocca Acked-by: Rob Herring Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron

iio: st_sensors: verify interrupt event to status

2016-04-19T18:58:12+00:00

This makes all ST sensor drivers check that they actually have new data available for the requested channel(s) before claiming an IRQ, by reading the status register (which is conveniently the same for all ST sensors) and check that the channel has new data before proceeding to read it and fill the buffer. This way sensors can share an interrupt line: it can be flaged as shared and then the sensor that did not fire will return NO_IRQ, and the sensor that fired will handle the IRQ and return IRQ_HANDLED. Cc: Giuseppe Barba Cc: Denis Ciocca Signed-off-by: Linus Walleij Signed-off-by: Jonathan Cameron

Merge 4.6-rc3 into staging-next

2016-04-11T16:30:50+00:00

This resolves a lot of merge issues with PAGE_CACHE_* changes, and an iio driver merge issue. Signed-off-by: Greg Kroah-Hartman