kernel/git/stable/linux.git/drivers/phy/freescale/Makefile, branch master

phy: lynx-10g: new driver

2026-06-11T07:09:47+00:00

Introduce a driver for the networking lanes of the 10G Lynx SerDes block, present on the majority of Layerscape and QorIQ (Freescale/NXP) SoCs. As with the 28G Lynx, the SerDes lanes come pre-initialized out of reset and the consumers use them that way outside the Generic PHY framework (for networking, the static configuration remains for the entire SoC lifetime, whereas for SATA and PCIe, the hardware reconfigures itself automatically for other link speeds). The need for the Generic PHY framework comes specifically for networking use cases where a static lane configuration is not sufficient. For example a network MAC is connected to an SFP cage, where various SFP or SFP+ modules can be connected. Each of them may require a different SerDes protocol (SGMII, 1000Base-X, 10GBase-R), which phylink + sfp-bus are responsible of figuring out. The phylink drivers are: - enetc - felix - dpaa_eth (fman_memac) - dpaa2-eth - dpaa2-switch and they all need to reconfigure the SerDes for the requested link mode, using phy_set_mode_ext() (and phy_validate() to see if it is supported in the first place). Note that SerDes 2 on LS1088A is exclusively non-networking, so there is currently no need for this driver. Therefore we skip matching on its compatible string and do not probe on that device. Co-developed-by: Ioana Ciornei Signed-off-by: Ioana Ciornei Signed-off-by: Vladimir Oltean Link: https://patch.msgid.link/20260610151952.2141019-16-vladimir.oltean@nxp.com Signed-off-by: Vinod Koul

phy: lynx-28g: move lane mode helpers to new core module

2026-06-11T07:09:46+00:00

Do some preparation work for the introduction of the lynx-10g driver, which will share a common backbone with the 28G Lynx SerDes. This is just trivial stuff which can be moved without any surgery, and is easy to follow but otherwise pollutes more serious changes. The lane modes themselves are exported to a public header, because on the 10G Lynx, the hardware requires implementing a procedure called "RCW override". This requires coordination with drivers/soc/fsl/guts.c to tell it that a SerDes lane needs to be switched to a different protocol (enum lynx_lane_mode). Signed-off-by: Vladimir Oltean Link: https://patch.msgid.link/20260610151952.2141019-4-vladimir.oltean@nxp.com Signed-off-by: Vinod Koul

phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support

2024-06-15T12:22:01+00:00

Add i.MX8QM HSIO PHY driver support. i.MX8QM HSIO has three lane PHY instances, and can be bound to the following controllers in the different use cases listed in below table. - two lanes capable PCIEA controller. - one lane PCIEB controller. - AHCI SATA controller. i.MX8QM HSIO PHYs support the following use cases. +----------------------------------------------------+ | | Lane0| Lane1| Lane2| |-------------------------------|------|------|------| | use case 1: PCIEAX2SATA | PCIEA| PCIEA| SATA | |-------------------------------|------|------|------| | use case 2: PCIEAX2PCIEB | PCIEA| PCIEA| PCIEB| |-------------------------------|------|------|------| | use case 3: PCIEAPCIEBSATA | PCIEA| PCIEB| SATA | +----------------------------------------------------+ Signed-off-by: Richard Zhu Reviewed-by: Frank Li Link: https://lore.kernel.org/r/1716962565-2084-3-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Vinod Koul

phy: freescale: add Samsung HDMI PHY

2024-03-28T18:57:06+00:00

This adds the driver for the Samsung HDMI PHY found on the i.MX8MP SoC. Based on downstream implementation from Sandor Yu . According to the TRM, the PHY receives parallel data from the link and serializes it. It also sets the PLL clock needed for the TX serializer. Tested-by: Luca Ceresoli Tested-by: Richard Leitner Co-developed-by: Marco Felsch Signed-off-by: Marco Felsch Signed-off-by: Lucas Stach Tested-by: Alexander Stein Tested-by: Frieder Schrempf # Kontron BL Signed-off-by: Adam Ford Tested-by: Marek Vasut Tested-by: Luca Ceresoli Tested-by: Tommaso Merciai Link: https://lore.kernel.org/r/20240227220444.77566-3-aford173@gmail.com Signed-off-by: Vinod Koul

phy: freescale: Add i.MX8qm Mixel LVDS PHY support

2022-07-08T05:13:20+00:00

Add Freescale i.MX8qm LVDS PHY support. The PHY IP is from Mixel, Inc. Signed-off-by: Liu Ying Link: https://lore.kernel.org/r/20220706034810.2352641-4-victor.liu@nxp.com Signed-off-by: Vinod Koul

phy: add support for the Layerscape SerDes 28G

2022-03-14T10:41:50+00:00

This patch adds a new generic PHY driver to support the Lynx 28G SerDes block found on some of the Layerscape SoCs such as LX2160A. At the moment, only the following Ethernet protocols are supported: SGMII/1000Base-X and 10GBaseR. SerDes lanes which are not running an Ethernet protocol or a currently supported Ethenet protocol will be left as it was configured through the RCW (Reset Configuration Word) at boot time. At probe time, the platform driver will read the current configuration of both PLLs found on a SerDes block and will determine what protocols are supported using that PLL. For example, if a PLL is configured to generate a clock net (frate) of 5GHz the only protocols sustained by that PLL are SGMII/1000Base-X (using a quarter of the full clock rate) and QSGMII using the full clock net frequency on the lane. On the .set_mode() callback, the PHY driver will first check if the requested operating mode (protocol) is even supported by the current PLL configuration and will error out if not. Then, the lane is reconfigured to run on the requested protocol. Signed-off-by: Ioana Ciornei Signed-off-by: David S. Miller

phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver

2021-12-14T14:32:53+00:00

Add the standalone i.MX8 PCIe PHY driver. Signed-off-by: Richard Zhu Tested-by: Marcel Ziswiler Reviewed-by: Tim Harvey Tested-by: Tim Harvey Link: https://lore.kernel.org/r/1638432158-4119-6-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Vinod Koul

Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

2019-07-01T13:04:59+00:00

phy: for 5.3 *) Add a new PHY driver for Qualcomm PCIe2 PHY *) Add a new PHY driver for Mixel DPHY present in i.MX8 *) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that PHY enable failed *) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to calling a sleeping function from invalid context *) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to imbalance powered flag *) Fix .cocci and sparse warnings Signed-off-by: Kishon Vijay Abraham I * tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay phy: meson-g12a-usb3-pcie: disable locking for cr_regmap phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs dt-bindings: phy: Add documentation for mixel dphy dt-bindings: phy-pxa-usb: add bindings phy: renesas: rcar-gen3-usb2: fix imbalance powered flag phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting phy: qcom-qmp: Correct READY_STATUS poll break condition phy: ti: am654-serdes: Make serdes_am654_xlate() static phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings phy: samsung: Use struct_size() in devm_kzalloc() phy: qcom: Add Qualcomm PCIe2 PHY driver dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY

phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs

2019-06-21T10:31:06+00:00

This adds support for the Mixel DPHY as found on i.MX8 CPUs but since this is an IP core it will likely be found on others in the future. So instead of adding this to the nwl host driver make it a generic PHY driver. The driver supports the i.MX8MQ. Support for i.MX8QM and i.MX8QXP can be added once the necessary system controller bits are in via mixel_dphy_devdata. Signed-off-by: Guido Günther Co-developed-by: Robert Chiras Signed-off-by: Robert Chiras Reviewed-by: Fabio Estevam Reviewed-by: Sam Ravnborg Signed-off-by: Kishon Vijay Abraham I

treewide: Add SPDX license identifier - Makefile/Kconfig

2019-05-21T08:50:46+00:00

Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman