| Age | Commit message (Collapse) | Author |
|---|
|
nvme_query_zone_info() returns either a negative errno or a positive
NVMe status code, but nvme_update_ns_info_block() only tests for the
negative case:
ret = nvme_query_zone_info(ns, lbaf, &zi);
if (ret < 0)
goto out;
If the device fails the Identify Namespace (I/O Command Set specific)
command, or the Identify Controller command issued by
nvme_set_max_append(), the positive status falls through and setup
continues with the zero-initialized zone info. nvme_update_zone_info()
then marks the queue zoned with chunk_sectors and ns->head->zsze set to
zero.
blk_validate_zoned_limits() does not check chunk_sectors, so the limits
commit succeeds. blk_revalidate_disk_zones() does reject the zero zone
size, but by then the limits are live and nothing rolls them back, so
I/O keeps being submitted to a zoned queue with a zero zone size and
disk_zone_no() shifts by ilog2(0):
nvme0n1: Invalid non power of two zone size (0)
UBSAN: shift-out-of-bounds in include/linux/blkdev.h:747:16
shift exponent -1 is negative
disk_zone_no include/linux/blkdev.h:747 [inline]
bio_straddles_zones include/linux/blkdev.h:1058 [inline]
blk_zone_wplug_handle_write block/blk-zoned.c:1423 [inline]
blk_zone_plug_bio.cold+0x25/0x1c8 block/blk-zoned.c:1605
blk_mq_submit_bio+0x18fb/0x2870 block/blk-mq.c:3196
submit_bh_wbc+0x575/0x740 fs/buffer.c:2824
__block_write_full_folio+0x728/0xdd0 fs/buffer.c:1933
Any device, firmware or NVMe-oF target that fails this one command
reaches this.
Skip the zoned limits update in that case, and log which of the two
things happened: during a revalidation the queue keeps the zone
geometry it was last validated with, and on a first scan the namespace
is registered without zoned limits, so that it is still available as a
handle for admin commands. Neither of the paths in
nvme_query_zone_info() that return a positive status logs anything, so
the failure would otherwise be silent.
zi.zone_size is an exact indicator: every path that returns a positive
status returns before it is assigned, and after that the only failure
left is -ENODEV, which the caller already handles.
Found by FuzzNvme.
Fixes: c85c9ab926a5 ("nvme: split nvme_update_zone_info")
Cc: stable@vger.kernel.org
Cc: Weidong Zhu <weizhu@fiu.edu>
Suggested-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chao Shi <coshi036@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
p1_rtc_read_time() called if (!regmap_test_bits(regmap, RTC_CTRL, RTC_EN))
to check if the RTC was enabled.
regmap_test_bits() returns 1 if the bit is set, 0 if not set, and a
negative error code (e.g. -EIO) if reading the control register fails.
Using !regmap_test_bits(...) evaluates a negative error code as boolean
false, causing I2C/regmap read failures to be ignored and incorrectly
proceeding to read time registers from a failing device.
Fix this by capturing the return value of regmap_test_bits() and returning
the error code if negative, or -EINVAL if the RTC is disabled.
Fixes: a6de182daa2b ("rtc: spacemit: support the SpacemiT P1 RTC")
Reviewed-by: Alex Elder <elder@riscstar.com>
Signed-off-by: Surendra Singh Chouhan <kr494167@gmail.com>
Link: https://patch.msgid.link/20260724135803.81223-1-kr494167@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
nvme_tcp_handle_c2h_data() finds the request by command id and checks
that it has a payload, but it does not check that the command asked for
data to be read. A controller that answers a write command with C2HData
therefore reaches nvme_tcp_recv_data(), where _copy_to_iter() hits
WARN_ON_ONCE(i->data_source) and returns 0. The receive path turns that
into -EFAULT and resets the controller.
No data is copied, so this is not memory corruption. What a controller
gets is a kernel warning it can raise at will, which is fatal on a host
booted with panic_on_warn.
The send path already knows the direction - it consults rq_data_dir()
when it builds a command - and nvme_tcp_handle_r2t() checks the length
and the offset of the request it names. The C2HData path does not check
the direction at all.
Reject a C2HData PDU whose command is not a read. Rejecting it fails
the command and resets the controller, as the neighbouring check in this
function does; what goes away is the warning.
[ 6.885580] ------------[ cut here ]------------
[ 6.886457] WARNING: lib/iov_iter.c:193 at _copy_to_iter+0x289/0x1330, CPU#0: kworker/0:1H/71
[ 6.888137] CPU: 0 UID: 0 PID: 71 Comm: kworker/0:1H Not tainted 7.2.0-rc5-NVMETCP-gf5098b6bae76 #1 PREEMPT(lazy)
[ 6.891165] Workqueue: nvme_tcp_wq nvme_tcp_io_work
[ 6.891875] RIP: 0010:_copy_to_iter+0x289/0x1330
[ 6.903739] Call Trace:
[ 6.904085] <TASK>
[ 6.909254] __skb_datagram_iter+0x433/0x820
[ 6.911026] skb_copy_datagram_iter+0x37/0x120
[ 6.911622] nvme_tcp_recv_skb+0xa07/0x4320
[ 6.913378] __tcp_read_sock+0x1ab/0x810
[ 6.915788] nvme_tcp_try_recv+0x152/0x1e0
[ 6.918222] nvme_tcp_io_work+0x1e4/0x6c0
[ 6.926906] </TASK>
[ 6.927226] ---[ end trace 0000000000000000 ]---
[ 6.927878] nvme nvme0: queue 1 failed to copy request 0x71 data
[ 6.928709] nvme nvme0: receive failed: -14
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Andrey Golovko <andrey.golovko@gmail.com> says:
v1 was a single patch that powered the SDCA Function up in the port
PRE_PREP callback:
https://lore.kernel.org/all/20260813001500.9218-1-andrey.golovko@gmail.com/
Mark asked whether that does the right thing when userspace restarts the
stream with SNDRV_PCM_IOCTL_RESUME instead of preparing it, and pointed
out that a stream can also be suspended while prepared; Vijendar agreed.
The answer to the first question is no, and it is reproducible on this
machine, so v2 adds a patch to fix that path. The second case turns out
to be a wider gap that neither patch closes; it is described at the end.
Measured on an ASUS ProArt PX13 HN7306EAC (AMD ACP7.0, two TAS2783 on
SDW1). A test program plays a 440/660 Hz tone straight to the hw
device, the machine goes through an s2idle cycle, and on -ESTRPIPE the
program calls snd_pcm_resume() only - never snd_pcm_prepare(). The tone
is measured through the internal microphone against the noise floor of
the same run, and the peripheral registers are read out of band.
With v1 alone (broonie/sound for-next + v1):
before suspend after snd_pcm_resume()
DP1 PrepareCtrl 0x1 / 0x2 0x0 / 0x0
PDE23 req / act 0x0 / 0x0 0x3 / 0x3
tone 440 / 660 Hz +65.5 / +75.2 dB -1.7 / +1.8 dB
snd_pcm_resume() returned 0 and the PCM stayed RUNNING, so nothing in
the stack reported a failure - the speakers were simply silent. The
ports were never prepared again, so the PRE_PREP callback v1 relies on
was never reached.
With this series:
before suspend after snd_pcm_resume()
DP1 PrepareCtrl 0x1 / 0x2 0x1 / 0x2
PDE23 req / act 0x0 / 0x0 0x0 / 0x0
tone 440 / 660 Hz +73.7 / +88.3 dB +73.7 / +88.5 dB
ChannelEn also moved to the other bank across the cycle, as it should
when the ports are prepared afresh.
The ordinary path is unaffected. The same test recovering with
snd_pcm_prepare() instead of snd_pcm_resume(), on the same build, gives
+79.8 / +86.9 dB after the cycle with the ports prepared and the bank
switched back.
This also explains the negative test Robin Everaars reported for v1 on
the same board earlier today: playback opened without an error, both
amplifiers stayed attached, and the speakers were silent - which is what
this path looks like from userspace.
The case this series does not cover
===================================
A stream that is suspended while merely PREPARED never sees a trigger at
all: snd_pcm_do_suspend() returns early when the stream is not running,
and snd_pcm_do_resume() returns early unless the suspended state was
RUNNING or DRAINING. Userspace then calls snd_pcm_start(), the ports
are enabled, and the peripheral has lost its port state without anything
in the path noticing. Patch 1 cannot help there - the SoundWire stream
is still SDW_STREAM_PREPARED, so sdw_prepare_stream() is a no-op by
design - and neither can the codec, which has no way to tell the core
that its ports went away.
The bus does know: the peripheral goes UNATTACHED and comes back
uninitialized. Making that invalidate the prepared state of the streams
it takes part in looks like the right place to me, but it is a core
change and I have not written it. Say if it belongs in this series.
Link: https://patch.msgid.link/20260813194000.10412-1-andrey.golovko@gmail.com
|
|
A Data Port cannot complete channel preparation while the SDCA Function
is powered down: the peripheral raises the channel's bit in
DPn_PrepareStatus and never clears it.
tas_sdw_hw_params() takes care of that for a stream that is being set
up, and the retry loop there says so - "ensure power on so that port
prepare succeeds". Port preparation, however, also happens on a stream
that is merely re-prepared, without hw_params() running again. That is
what userspace does after a suspend in which the peripheral lost power:
snd_pcm_prepare() reaches .prepare and sdw_prepare_stream(), the port is
prepared afresh, but PDE23 is still at the PS3 reset default because
nothing wrote it since the device came back.
The result is silence with no error anywhere. The codec sets
simple_ch_prep_sm, so sdw_prep_deprep_slave_port() skips the
NOT_PREPARED poll, and a port that never prepares is indistinguishable
from a healthy one.
Power the Function up in the PRE_PREP callback, immediately before the
PrepareCtrl write it already performs, so that preparation has what it
needs on every path that prepares a port.
Measured on an ASUS ProArt PX13 (AMD ACP7.0, two TAS2783): after s2idle
with ~100 s of S0i3 residency, DPn_PrepareStatus stays at the channel
mask and there is no audio; writing PDE23 PS0 and re-issuing the prepare
clears it within 1 ms and audio returns.
Signed-off-by: Andrey Golovko <andrey.golovko@gmail.com>
Link: https://patch.msgid.link/20260813194000.10412-3-andrey.golovko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A peripheral loses its Data Port configuration when the controller is
power-gated during system suspend, so the ports have to be prepared
again before the stream can be enabled. That happens on its own when
userspace calls snd_pcm_prepare() after SNDRV_PCM_STATE_SUSPENDED, but
an application is also allowed to restart the stream with
SNDRV_PCM_IOCTL_RESUME on a card that advertises SNDRV_PCM_INFO_RESUME,
as the AMD ACP platforms do. That path only reaches the trigger
callback, sdw_enable_stream() writes the channels of ports that were
never prepared, and playback silently produces nothing: the PCM keeps
running, no error is reported anywhere, and the speakers stay quiet
until the stream is torn down and set up again.
Prepare the stream on SNDRV_PCM_TRIGGER_RESUME, before enabling it.
The SoundWire core expects exactly this: sdw_prepare_stream() accepts a
disabled stream and then reapplies the bus parameters without
recomputing them, which it documents as the resume case.
Signed-off-by: Andrey Golovko <andrey.golovko@gmail.com>
Link: https://patch.msgid.link/20260813194000.10412-2-andrey.golovko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Unlike the CRTC degamma path, which is guarded by
amdgpu_dm_verify_lut_sizes(), the per-plane degamma LUT size was never
validated before use. __set_dm_plane_degamma() passed the user-supplied
size straight into __is_lut_linear() and, for a non-linear LUT, into
__set_input_tf() -> __drm_lut_to_dc_gamma(), the latter always iterating
MAX_COLOR_LUT_ENTRIES entries regardless of the actual LUT size.
A malformed AMD_PLANE_DEGAMMA_LUT blob (e.g. a single entry) could thus
trigger a divide-by-zero in __is_lut_linear() or an out-of-bounds read in
__drm_lut_to_dc_gamma(). Reject any plane degamma LUT whose size does not
match MAX_COLOR_LUT_ENTRIES, mirroring the invariant the code already
asserts a few lines below (and which the CRTC path enforces).
The AMD_PLANE_DEGAMMA_LUT property is only exposed on builds with
AMD_PRIVATE_COLOR defined.
Fixes: 980f8710075a ("drm/amd/display: add plane degamma TF and LUT support")
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
__is_lut_linear() computes the expected value of each entry with
expected = i * MAX_DRM_LUT_VALUE / (size - 1);
If it is ever called with a single-entry LUT, size - 1 is zero and the
kernel takes a divide error (#DE). A LUT with fewer than two entries
cannot describe a linear mapping anyway, so return false early instead
of dividing by zero.
Fixes: 086247a4b2fb ("drm/amd/display: Use 4096 lut entries")
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If we end up emitting a VM fence keep pipeline sync
associated with that fence. If not, emit them as
part of the IB fence.
v2: fix need_pipe_sync handling
v3: simplify the function
Cc: David Rosca <david.rosca@amd.com>
Fixes: cb1e657ccac8 ("drm/amdgpu: handle GDS and SPM without a VM fence")
Reviewed-by: David Rosca <david.rosca@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If the supplied msg[2] (num_buffers) is 0x3FFFFFFF, the expression
6 + num_buffers * 4 wraps to 2 and the bounds check passes, letting
the parser loop far past the end of the message BO. Triggering it
additionally requires a ~4GiB mapping so that msg[1] survives the
earlier "header does not fit in BO" check.
Rewrite the test in division form, which is overflow-free by
construction. Also update the message to reflect that msg is invalid.
Fixes: b193019860d6 ("drm/amdgpu/vcn3: Prevent OOB reads when parsing dec msg")
Fixes: 0a78f2bac142 ("drm/amdgpu/vcn4: Prevent OOB reads when parsing dec msg")
Cc: stable@vger.kernel.org
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The Apple iMac11,1 (27-inch, Late 2009) uses a Mobility Radeon HD 4850
(RV770/DCE3.1) with a 2560x1440 internal panel on an internal
DisplayPort path. Without this fix the display stays dark under KMS.
This machine suffers from the same issue as iMac10,1 and iMac11,2:
Apple routes the internal display through Link B of the DIG encoder
instead of Link A. Add iMac11,1 to the existing DMI quirk and move
the Apple-specific encoder assignment into its own block, independent
of the DCE version check.
Additionally, the 2560x1440 panel requires RADEON_PLL_USE_FRAC_FB_DIV
and ATOM_ENCODER_CMD_DP_VIDEO_ON, limited to iMac11,1 via dmi_match()
to avoid affecting other boards.
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Gilles Risch <gilles.risch@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When a queue is hung, the hang_detect_work is the
only way to recover it. However in amdgpu_userq_destroy(),
the hang_detect_work is cancelled too early,
resulting in amdgpu_userq_wait_for_last_fence()
may never return, leaving an uninterruptible dma_fence_wait()
hang there.
To fix this problem, this commit moves the cancelling of
hang_detect_work after amdgpu_userq_wait_for_last_fence(), and it has
to be before the unmap helper, because hang_detect_work resets the
queue, so it races with amdgpu_userq_unmap_helper() for MES operations
and queue state.
This commit splits amdgpu_userq_cleanup() into two parts:
1) amdgpu_userq_detach_doorbell(), which detaches the queue from
userq_doorbell_xa. This has to be called before the cancel, otherwise
the IRQ handlers (for example amdgpu_userq_process_fence_irq)
can re-schedule the hang_detect_work and the cancel is not final.
2) amdgpu_userq_fence_driver_free(), this has to be called after the
unmap helper, because it can release the seq64 slot that the GPU
writes fence values to.
Only one cancel_delayed_work_sync(&queue->hang_detect_work) is needed,
so other redundancies are removed.
Signed-off-by: Zhu Lingshan <lingshan.zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
profile_lock_device() may return negive error code,
so the type of the return value should be int,
not uint32
Signed-off-by: Zhu Lingshan <lingshan.zhu@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When amdgpu_init_minimal_xgmi is used, SDMA engines init
is delayed so amdgpu_ttm_enable_buffer_funcs must be
called later.
Without this, the check for num_buffer_funcs_scheds will
fail and using ttm buffer funcs later will fail.
Given that amdgpu_ttm_enable_buffer_funcs is a no-op if
amdgpu_in_reset() returns true, the call has to occur
after the reset lock is dropped.
Cc: stable@vger.kernel.org
Fixes: e4029f7a9474 ("drm/amdgpu: only use working sdma schedulers for ttm")
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Introduce a helper to consolidate the vga_switcheroo registration condition
used by the init and fini paths.
Keep the explicit pci_is_thunderbolt_attached() check, as dev_is_removable()
does not provide equivalent coverage for Thunderbolt-attached GPUs.
This ensures such devices remain excluded from switcheroo registration while
preserving the existing PX and Apple gmux handling.
Cc: stable@vger.kernel.org
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Like the MES scheduler ring, the KIQ ring sets no_scheduler = true and uses a
polling fence, so it is skipped by the force-completion loop in
amdgpu_device_pre_asic_reset(). Its hw fence value lives in wb (GTT) memory and
survives a MODE1 reset while fence_drv.sync_seq keeps advancing, so after a
reset the first KIQ submission can poll forever on a seq that is never written
back.
Force complete the KIQ ring fences too so their hw fence is realigned to
sync_seq.
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
rptr and wptr of a userq are 8 bytes aligned, and may
not placed on a page boundary.
This commit checks whether rptr and wptr are 8 bytes
aligned, and expectes 8 bytes when validates rptr/wptr VA.
With above changes, this commit fixes an regression
in amdgpu_userq_input_va_validate, where
end_addr is caculated by:
check_add_overflow(start_addr, expected_size - 1, &end_addr).
Wptr and rptr are very likely not to be page aligned,
when validating rptr and wptr, if they are located in the last
mapped page(or only one page is mapped)
and expected_size is PAGE_SIZE, end_addr will exceed the last
mapped page, means (end_addr >> AMDGPU_GPU_PAGE_SHIFT) > va_map->last,
and causing an -EINVAL, even it is a valid VA.
Signed-off-by: Zhu Lingshan <lingshan.zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Fixes: c0122bf2ccb1 ("drm/amdgpu: fix userq VA validation for sub-page buffers")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The MES scheduler ring has no drm scheduler (no_scheduler = true), so it is
skipped by the force-completion loop in amdgpu_device_pre_asic_reset(). It uses
a polling fence whose hw value lives in wb (GTT) memory and survives a MODE1
reset, while fence_drv.sync_seq keeps advancing for every packet.
When the reset is triggered because MES itself stopped responding, the
timed-out packets advance sync_seq past the last hw fence value MES wrote.
After resume the first MES submission polls forever on a seq that is never
written back, failing the resume and wedging the box on a second reset:
amdgpu: MES ring buffer is full.
amdgpu: *ERROR* ring gfx_0.0.0 test failed (-110)
amdgpu: resume of IP block <gfx_v11_0> failed -110
amdgpu: GPU reset end with ret = -110
Force complete the MES scheduler ring fences together with the scheduler rings
so their hw fence is realigned to sync_seq.
v2: cover all XCCs (one scheduler ring each), not just mes.ring[0].
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In standalone mode the ip_discovery sysfs tree is built from a verbatim
copy of the discovery binary taken before reg_base_init() collapses the
64bit base addresses in place. Decoding as 32bit there yields interleaved
zeros. Decode base_address_64[] in that case; keep reading the already
collapsed adev->discovery.bin as-is otherwise.
Fixes: 402e04f11ff7 ("drm/amdgpu: Export ip_discovery sysfs on probe failure")
Cc: stable@vger.kernel.org
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Custom brightness curves use an 8-bit input signal. After exporting the
full PWM range to userspace, the curve normalizer still divides requests
by the physical PWM span. On panels with a nonzero minimum PWM level,
this can produce a curve input greater than 255 and send an invalid
backlight level to DC.
Scale the userspace [0..max] range to the curve's [0..255] range
instead. This retains the full advertised range and keeps the reverse
readback conversion unchanged.
Fixes: 8dbd72cb7900 ("drm/amd/display: Export full brightness range to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Akhmed Zhitaev <zhitaevakh@gmail.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
(Move to amdgpu_dm_backlight.c)
Link: https://patch.msgid.link/20260813170959.22073-1-zhitaevakh@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_userq_wait_return_fence_info() calls drm_exec_init() without
DRM_EXEC_IGNORE_DUPLICATES. When the same GEM object appears more than
once across the read/write BO handle lists submitted by userspace,
drm_exec_lock_obj() returns -EALREADY the second time it locks that
object, which aborts the fence resolution pass instead of treating the
repeat as a no-op.
Add DRM_EXEC_IGNORE_DUPLICATES so duplicate objects are silently
skipped on the second lock attempt.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_userq_wait_count_fences() calls drm_exec_init() without
DRM_EXEC_IGNORE_DUPLICATES. When the same GEM object appears more than
once across the read/write BO handle lists submitted by userspace,
drm_exec_lock_obj() returns -EALREADY the second time it locks that
object, which aborts the fence-counting pass instead of treating the
repeat as a no-op.
Add DRM_EXEC_IGNORE_DUPLICATES so duplicate objects are silently
skipped on the second lock attempt.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_userq_signal_ioctl() calls drm_exec_init() without
DRM_EXEC_IGNORE_DUPLICATES. When the same GEM object appears more than
once across the read/write BO handle lists submitted by userspace,
drm_exec_lock_obj() returns -EALREADY the second time it locks that
object, which aborts the ioctl instead of treating the repeat as a
no-op.
Add DRM_EXEC_IGNORE_DUPLICATES so duplicate objects are silently
skipped on the second lock attempt, matching the intended semantics of
locking a set of (possibly overlapping) BOs before publishing a fence
on them.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_userq_buffer_vas_mapped() checks whether all VAs
of a queue are mapped before restoring it.
So that HW won't access any invalid addresses.
Currently, this function assumes all VAs are mapped if
any VA of a queue has been mapped, which is wrong.
This commit fixes this problem by examining all VAs of
a queue and reporting false if any of them is not mapped.
Signed-off-by: Zhu Lingshan <lingshan.zhu@amd.com>
Reviewed-by: Sunil Khatri <sunil.khatri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
amdgpu_pci_probe() calls pm_runtime_use_autosuspend(), but
amdgpu_pci_remove() does not call the matching
pm_runtime_dont_use_autosuspend().
If the autosuspend delay is set to a negative value while autosuspend
is enabled, the runtime PM core increments usage_count to prevent
runtime suspend. Without calling pm_runtime_dont_use_autosuspend()
during teardown, this reference is not dropped and usage_count remains
unbalanced.
The documentation for pm_runtime_use_autosuspend() also notes that it
is important to undo it with pm_runtime_dont_use_autosuspend() at
driver exit time, unless runtime PM was initially enabled with
devm_pm_runtime_enable().
Add the missing pm_runtime_dont_use_autosuspend() call to the remove
path.
This issue was found by manual code inspection.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Cc: stable@vger.kernel.org
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260808120934.2813010-1-lgs201920130244@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pci_is_thunderbolt_attached() requires an upstream PCI bridge with
is_thunderbolt set from an Intel Thunderbolt VSEC. This does not cover
the affected ASM4242 USB4 PCI hierarchy:
00:02.2
\- 0f:00.0 [1b21:2421]
+- 10:01.0 [1b21:2423] -> 45:00.0 -> 46:00.0
| -> 47:00.0 -> 48:00.0 -> 49:00.0 [1002:7590]
\- 10:03.0 -> 76:00.0 [1b21:2425] USB4 Host Router
The host router is outside the GPU upstream bridge chain, leaving no
ancestor with is_thunderbolt set. PCI core propagates DEVICE_REMOVABLE
below the external-facing PCIe tunnel. Disable Runtime PM when either
pci_is_thunderbolt_attached() or dev_is_removable() is true.
Cc: stable@vger.kernel.org
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Candice Li <candice.li@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pcf8563_clkout_register_clk() registers the CLKOUT clock provider with
of_clk_add_provider(), but nothing ever unwinds it: there is no
of_clk_del_provider() call and the driver has no remove callback. Each
of_clk_add_provider() allocates a struct of_clk_provider, takes a
reference on the OF node and adds an entry to the global of_clk_providers
list, none of which is released when the device is unbound. Every
bind/unbind (or module reload) therefore leaks a provider structure and
an of_node reference.
The clock itself is already device-managed (devm_clk_register()); only
the provider registration was not. Use devm_of_clk_add_hw_provider() so
the provider is removed automatically on unbind. Tie it to the parent
i2c device, whose OF node carries the #clock-cells and clock-output-names
properties (the RTC class device has no OF node of its own).
Fixes: a39a6405d5f9 ("rtc: pcf8563: add CLKOUT to common clock framework")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Yi Ding <yi.s.ding@gmail.com>
Link: https://patch.msgid.link/20260602035135.62264-1-yi.s.ding@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Creative Sound Blaster Play! 3 (041e:324d) exposes a Feature Unit
volume control with a range of -44.00 dB .. 0.00 dB over raw values
0..88, but raw value 0 is in fact a hard mute rather than -44.00 dB.
Tested on hardware.
Signed-off-by: Chad Talbott <chad.talbott@gmail.com>
Link: https://patch.msgid.link/20260819003237.452807-1-chad.talbott@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
pcxhr_probe() requests pcxhr_threaded_irq() before initializing
mgr->lock, even though the threaded handler takes that mutex.
Initialize the manager locks before request_threaded_irq() so an
early interrupt cannot run against uninitialized mutex state during
probe.
Fixes: 9bef72bdb26e ("ALSA: pcxhr: Use nonatomic PCM ops")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Link: https://patch.msgid.link/20260818144717.2269918-1-runyu.xiao@seu.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If an error occurs during startup of an IPMI interface, it may have
scheduled work to run. The work needs to be canceled before the
interface can be freed.
Reported-by: Nilay Shroff <nilay@linux.ibm.com>
Closes: https://sourceforge.net/p/openipmi/mailman/message/59375605/
Fixes: 62cd145453d5 ("ipmi:msghandler: Handle error returns from the SMI sender")
Cc: stable@vger.kernel.org # 7.0
Tested-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Corey Minyard <corey@minyard.net>
|
|
Implement suspend operation for vduse devices, so vhost-vdpa will offer
that backend feature and userspace can effectively suspend the device.
This is a must before get virtqueue indexes (base) for live migration,
since the device could modify them after userland gets them.
This patch does not implement resume, so VMM resets the whole device
to recover from a live migration failure. Resume optimization can be
implemented on top of these patches, as other vDPA devices have done in
the past.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707123344.244575-3-eperezma@redhat.com>
|
|
Next patches need to check suspend flag at this work item, and the
rwlock is used to protect the suspend flag update. If the work takes
the rwlock too it will produce a deadlock.
Make flushing work do nothing when called by de-initializing everything:
vq->ready, vq->kickfd, vq->cb.callback.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707123344.244575-2-eperezma@redhat.com>
|
|
Add the VDUSE_F_QUEUE_READY feature flag. This allows the kernel module
to explicitly signal userspace when a specific virtqueue has been
enabled.
In scenarios like Live Migration of VirtIO net devices, the dataplane
starts after the control virtqueue allowing QEMU to apply configuration
in the destination device.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707122502.239022-5-eperezma@redhat.com>
|
|
Add an ioctl to allow VDUSE instances to set the VDUSE features
supported by the userland VDUSE instance.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707122502.239022-4-eperezma@redhat.com>
|
|
Add an ioctl to allow VDUSE instances to query the available features
supported by the kernel module.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707122502.239022-3-eperezma@redhat.com>
|
|
This helps log the errors in next patches. The alternative is to
perform a linear search for it with class_find_device_by_devt(class, devt),
as device_destroy do for cleaning.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260707122502.239022-2-eperezma@redhat.com>
|
|
Fix a misspelling of "control" in the trace agent controller description.
Signed-off-by: GuoHan Zhao <zhaoguohan@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260720014506.90012-1-zhaoguohan@kylinos.cn>
|
|
Fix a misspelling of "userspace" in the vringh test description.
Signed-off-by: GuoHan Zhao <zhaoguohan@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260720014421.89345-1-zhaoguohan@kylinos.cn>
|
|
Reject VHOST_IOTLB_INVALIDATE messages with size == 0 to prevent
iova + size - 1 from underflowing to U64_MAX, which would
incorrectly delete the entire IOTLB.
Signed-off-by: xiongweimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260716030236.124322-1-xiongwm2026@163.com>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_irq() automatically logs
detailed error messages on failure. Remove the now-redundant
driver-specific dev_err() calls.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260716141349.158824-1-panchuang@vivo.com>
|
|
virtnet_poll_cleantx() contains a do-while loop that cleans up
transmitted TX buffers and calls virtqueue_enable_cb_delayed() to check
whether more buffers need processing. When the virtio backend stops
responding during guest reboot, used->idx is never updated, so
virtqueue_enable_cb_delayed() always returns false and the loop never
terminates. Then it will block reboot process, and the guest will hang.
The problem occurs during guest reboot under network traffic:
1. kernel_restart() -> device_shutdown() traverses the device list
2. virtio_dev_shutdown() calls virtio_break_device() which sets
vq->broken = true
3. virtio_dev_shutdown() then calls virtio_synchronize_cbs() to wait
for in-flight callbacks to complete
4. A virtio interrupt fires, softirq is deferred to ksoftirqd which
calls net_rx_action() -> virtnet_poll() -> virtnet_poll_cleantx()
5. virtnet_poll_cleantx() enters the do-while loop and never exits
because the QEMU backend has stopped updating used->idx, despite
vq->broken having been set to true in step 2.
Since the loop runs inside ksoftirqd (a SCHED_OTHER kthread), it is
visible to the scheduler and does not trigger a hard lockup. However,
the kthread never leaves the loop, so RCU detects it as a CPU stall
and reports it periodically. Meanwhile, the reboot process remains
blocked in device_shutdown() because virtio_dev_shutdown() cannot
complete its synchronization step, and the guest hangs permanently.
This can be reproduced on a guest with a virtio-net device: run iperf3
traffic in the guest, then trigger reboot. The reboot occasionally hangs
permanently with RCU stall on ksoftirqd.
Observed on ARM64 KVM guest:
CPU#1 RCU stall (ksoftirqd/1), repeated periodically:
virtqueue_enable_cb_delayed_split <- virtnet_poll <- __napi_poll <-
net_rx_action <- handle_softirqs <- run_ksoftirqd <-
smpboot_thread_fn <- kthread
Fix by adding a vq->broken check in virtqueue_enable_cb_delayed(), so
that the loop exits immediately when the device is broken, allowing
the device shutdown to proceed.
Signed-off-by: Jinqian Yang <yangjinqian1@huawei.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260716115940.394832-1-yangjinqian1@huawei.com>
|
|
mlx5_vdpa_change_map() must install the new MR before rebuilding or
resuming virtqueues, because both paths read the MR keys from
mvdev->mres.mr[].
If rebuilding the virtqueue resources fails, the new MR must not remain
installed after its reference is released. Keep an extra reference to
the old MR before replacing it. On setup failure, restore the old MR;
the saved reference then becomes the map reference, while replacing the
new MR drops its map reference.
Make mlx5_vdpa_change_map() consume new_mr on all error paths so that
set_map_data() does not release an MR already released during rollback.
v2:
- Keep the new MR installed while virtqueues are rebuilt.
- Restore the old MR only after setup_vq_resources() fails.
Signed-off-by: Weimin Xiong <xiongwm2026@163.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260716054353.155805-1-xiongwm2026@163.com>
|
|
I no longer have the bandwidth to look after these drivers, so I'm
leaving them in the able hands of my co-maintainers.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260715151908.1534002-1-gsomlo@gmail.com>
|
|
Correct "actipn" to "action".
Signed-off-by: xiongweimin <xiongweimin@kylinos.cn>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Acked-by: David Hildenbrand (Arm) <david@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260714032417.201353-1-xiongwm2026@163.com>
|
|
Correct "readind" and "the an error" in the DPU control path comments.
Signed-off-by: xiongweimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260714024527.188645-1-15927021679@163.com>
|
|
Use "a virtio" rather than "an virtio".
Signed-off-by: xiongweimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260714024513.188571-1-15927021679@163.com>
|
|
Correct missing "if" in the add_range_ctx return description, and
align vhost_iotlb_alloc documentation with its NULL return on
allocation failure.
Signed-off-by: xiongweimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260714024434.188302-1-15927021679@163.com>
|
|
RTC class operations run with rtc_device.ops_lock held. The virtio RTC
alarm requests currently wait without a timeout for the device to return
their requestq buffers.
On surprise removal, virtio-pci marks the virtqueues broken before
unregistering the virtio device. If an alarm request is waiting when the
device stops responding, viortc_remove() blocks in viortc_class_stop()
while trying to acquire ops_lock. The request cannot complete and device
removal hangs until the waiting task is signalled.
Use the same 60-second timeout as clock read requests for alarm reads,
alarm programming, and alarm interrupt enable requests. The existing
message reference counting keeps a timed-out request alive until a late
response or device teardown.
Fixes: 9d4f22fd563e ("virtio_rtc: Add RTC class driver")
Assisted-by: Codex:gpt-5.6-sol
Signed-off-by: GuoHan Zhao <zhaoguohan@kylinos.cn>
Reviewed-by: Peter Hilber <peter.hilber@oss.qualcomm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260714024352.71307-1-zhaoguohan@kylinos.cn>
|
|
In alloc_inout(), the qpc field offset was computed using
MLX5_ADDR_OF(rst2init_qp_in, ...) in both the INIT2RTR_QP and
RTR2RTS_QP cases. This is a copy-paste error: each case should use
its own input structure type to get the correct qpc offset.
Fix the INIT2RTR_QP case to use MLX5_ADDR_OF(init2rtr_qp_in, ...)
and the RTR2RTS_QP case to use MLX5_ADDR_OF(rtr2rts_qp_in, ...).
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260706060902.2341-1-lirongqing@baidu.com>
|
|
The driver has a match table for the pci bus wired into its driver
structure, but the table is not exported with MODULE_DEVICE_TABLE().
Add the missing MODULE_DEVICE_TABLE() entry so module alias information
is generated for automatic module loading.
This is a source-level fix. It does not claim dynamic hardware
reproduction; the evidence is the driver-owned match table, its use by
the driver registration structure, and the missing module alias
publication.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260705002546.85004-1-pengpeng@iscas.ac.cn>
|
