| Age | Commit message (Collapse) | Author |
|---|
|
According to the source code, flowlabel_consistency must be
deactivated for the IPV6_FL_F_REFLECT flag to work. Since
ipv6_flowlabel_mgr now runs in its own network namespace, do this
directly from the test binary. Attempt to disable
net.ipv6.flowlabel_consistency and skip the reflect test if that
fails. A disabled flowlabel_consistency does not affect the remaining
features being tested on the file, and failing to disable is not fatal
and skips the reflect test only.
The previously defined tcp_listen and tcp_connect helpers were reused,
since the connection flow required for REFLECT validation is very
similar to REMOTE.
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Link: https://patch.msgid.link/20260807220942.421382-5-marcelomspessoto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Have ipv6_flowlabel_mgr create and configure its own network
namespace (unshare(CLONE_NEWNET) + bring up lo), the same way
ipv6_fragmentation.c and icmp_rfc4884.c already do, instead of
relying on the in_netns.sh wrapper script.
The setup can then be reused across tests through fixtures and
provide isolated network environments for each test in the case
of a future adoption of kselftest_harness.
It also avoids the leak of modifications to the netns in case the
user runs the test file directly, outside the wrapper and without
the in_netns.sh file.
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Link: https://patch.msgid.link/20260807220942.421382-4-marcelomspessoto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This flag retrieves the flow label seen by the socket at connection
setup via a getsockopt query. Therefore, the validation of this flag
requires a brief connection setup (source code for flow label shows
it must be TCP).
The simple TCP connection logic was wrapped inside two simple helpers,
because there are other uncovered features of flow label mgr that
could benefit from it (such as IPV6_FL_F_REFLECT).
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Link: https://patch.msgid.link/20260807220942.421382-3-marcelomspessoto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RENEW was the only flow label action without selftests coverage.
Assert renew returns no error on correct usage and fails for labels
that do not exist.
This test is based on the previously implemented EXCL share test,
which demonstrates that a new flow label with the same value can be
created after the linger period. Renew is used here to show that a
flow label can last longer and block a new flow label creation after
the previous linger time. This test, however, demands sleep during
execution, and should be placed as a conditional test under the -l
option.
The addition of the expect_fail_errno helper is necessary to assert
the corresponding error when a function can fail in multiple ways.
Signed-off-by: Marcelo Mendes Spessoto Junior <marcelomspessoto@gmail.com>
Link: https://patch.msgid.link/20260807220942.421382-2-marcelomspessoto@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcf_action_exec() handles TC_ACT_GOTO_CHAIN by first checking
rcu_access_pointer(a->goto_chain) and then calling
tcf_action_goto_chain_exec(), which does a second, independent
rcu_dereference_bh(a->goto_chain) read and immediately dereferences
chain->filter_chain. A concurrent tcf_action_set_ctrlact() (e.g. the gact
replace path) can clear a->goto_chain between the two reads, so the second
read returns NULL and tcf_action_goto_chain_exec() dereferences NULL.
Fix the race by doing a single rcu_dereference_bh() read of a->goto_chain
in tcf_action_exec(), checking it once for NULL, and passing the resulting
chain pointer into tcf_action_goto_chain_exec(). This turns the split
check/use into a single check/use on one value.
Fixes: ee3bbfe806cd ("net/sched: let actions use RCU to access 'goto_chain'")
Reported-by: vega@nebusec.ai
Tested-by: Victor Nogueira <victor@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Link: https://patch.msgid.link/20260809090928.868186-1-jhs@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tariq Toukan says:
====================
devlink: add generic device max_sfs parameter
This series by Nikolay introduces a new generic devlink device
parameter, max_sfs, to control the number of light-weight NIC
subfunctions (SFs) that can be created on a device.
The first patch adds the generic devlink parameter and infrastructure
support.
The second patch implements support for the parameter in the mlx5
driver.
With this addition, users can enable or disable SF creation directly via
devlink, without relying on external vendor-specific tools.
====================
Link: https://patch.msgid.link/20260806073037.3001886-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement max_sfs generic parameter to allow users to control the total
light-weight NIC subfunctions that can be created using devlink instead
of external vendor tools. A value of 0 will effectively disable creation
of new subfunction devices. A warning is sent to user-space via extack
(returning extack without error code is interpreted as a warning by
user-space tools). The maximum value is capped at U16_MAX.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260806073037.3001886-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new generic devlink device parameter (max_sfs) to control if and
how many light-weight NIC subfunctions can be created. Subfunctions are
a light-weight network functions backed by an underlying PCI function.
Their lifecycle can already be managed by devlink, but currently users
cannot enable them in the device. They can be enabled/disabled only via
external vendor tools. This parameter allows subfunctions to be enabled
(>0) or disabled (0) via devlink. A subsequent patch will add support
for max_sfs to the mlx5 driver.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260806073037.3001886-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
List all the files of the QCA8K DSA Switch driver and add myself as
maintainer.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260810143740.652804-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tung Quang Nguyen has been working as the de facto TIPC maintainer
for a few years now. Make sure the MAINTAINERS file reflects this
reality. Dealing with the flood of AI patches is a significant
effort, and Tung's work and responsiveness is exemplary.
Link: https://patch.msgid.link/20260810180148.680425-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported a WARNING in __dev_queue_xmit() triggered via tpacket_snd():
skb_assert_len
WARNING: at include/linux/skbuff.h:2753 skb_assert_len
WARNING: at __dev_queue_xmit+0x21bc/0x4970 net/core/dev.c:4781
Call Trace:
<TASK>
dev_queue_xmit include/linux/netdevice.h:3448 [inline]
packet_xmit+0x243/0x310 net/packet/af_packet.c:276
tpacket_snd net/packet/af_packet.c:2907 [inline]
packet_sendmsg+0x28d6/0x4eb0 net/packet/af_packet.c:3134
When sending 0-byte packets via TPACKET ring buffer on devices with no
hard header (e.g. dev->hard_header_len == 0), tpacket_fill_skb()
populates an skb with skb->len == 0 and returns 0. tpacket_snd() then
forwards this empty skb to packet_xmit(), causing __dev_queue_xmit() to
hit skb_assert_len(skb).
Similar checks exist in packet_snd() via commit dc633700f00f
("net/af_packet: check len when min_header_len equals to 0") and in
packet_sendmsg_spkt() via commit 6a341729fb31 ("af_packet: Don't send
zero-byte data in packet_sendmsg_spkt().").
Return -EINVAL in tpacket_fill_skb() when skb->len is zero to reject
zero-length packets in tpacket_snd().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+30b93b6845b19cc38581@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6a79e807.01d0871a.3a0d52.00ac.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260810150447.1220864-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the cleanup_srcu_struct() function, when iterating over per-cpu's
srcu_data, timer_delete_sync(&sdp->delay_work) is called to cancel the
delayed work before doing flush_work(&sdp->work).
However, suppose that timer_delete_sync() returns 1, which means that it
successfully deleted an pending timer before it had a chance to fire.
But this also means that the sdp->work will not be queued, so that the
subsequent flush_work(&sdp->work) will returns immediately without waiting
for anything. Taken together, all of this means that any recently queued
SRCU callbacks to not be invoked, which can result in memory leaks,
hangs, or worse.
Fix this by checking the return value of timer_delete_sync(), if it
returns 1, explicitly queue sdp->work so that the callbacks will be
invoked and the following flush_work() will correctly wait for all of
those callbacks to finish executing.
[ Zqiang: Apply feedback from Breno Leitao and kernel test robot. ]
Signed-off-by: Zqiang <qiang.zhang@linux.dev>
Tested-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
According to PCIe r7.0, sec 5.3.3.2, two link wakeup mechanisms are
defined: Beacon and WAKE#. Beacon is a hardware-only mechanism and is
invisible to software (sec 4.2.7.8.1). This change adds support for the
WAKE# mechanism in the PCI core.
According to the PCIe specification, multiple WAKE# signals can exist in a
system or several components in the hierarchy may share a single WAKE#
signal. In configurations involving a PCIe switch, each downstream port
(DSP) of the switch may be connected to a separate WAKE# line, allowing
each endpoint to signal WAKE# independently. From figure 5.4 in sec
5.3.3.2, WAKE# can also be terminated at the switch itself. Such topologies
are typically not described in Device Tree, therefore it is out of scope
for this series.
To support this, the WAKE# should be described in the device tree node of
the endpoint/bridge. If all endpoints share a single WAKE# line, then each
endpoint node shall describe the same WAKE# signal or a single WAKE# in the
Root Port node.
In pci_device_add(), PCI framework will search for the WAKE# in device
node. Once found, register for the wake IRQ through
dev_pm_set_dedicated_wake_irq() associates a wakeup IRQ with a device and
requests it, but the PM core keeps the IRQ disabled by default. The IRQ is
enabled by the PM core, only when the device is permitted to wake the
system, i.e. during system suspend and after runtime suspend, and only when
device wakeup is enabled.
If the same WAKE# GPIO is described in multiple device tree nodes, only the
first device that successfully registers the wake IRQ will succeed, while
subsequent registrations may fail. This limitation does not affect
functional correctness, since WAKE# is only used to bring the link to D0,
and endpoint-specific wakeup handling is resolved later through PME
detection (PME_EN is set in suspend path by PCI core by default).
When the wake IRQ fires, the wakeirq handler invokes pm_runtime_resume() to
bring the device back to an active power state, such as transitioning from
D3cold to D0. Once the device is active and the link is usable, the
endpoint may generate a PME, which is then handled by the PCI core through
PME polling or the PCIe PME service driver to complete the wakeup of the
endpoint.
WAKE# is added in dts schema and merged based on below links.
Link: https://lore.kernel.org/all/20250515090517.3506772-1-krishna.chundru@oss.qualcomm.com/
Link: https://github.com/devicetree-org/dt-schema/pull/170
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260707-wakeirq_support-v12-1-b4453f5bcc97@oss.qualcomm.com
|
|
__hfsplus_ext_write_extent() writes the cached extent record back into a
B-tree node using fd->entrylength as the length, and fd->entrylength is
derived in __hfs_brec_find() from two on-disk values:
fd->entrylength = len - keylen;
A crafted image can keep both len and keylen valid but make fd->entrylength
negative (keylen > len). __hfsplus_ext_write_extent() doesn't check
fd->entrylength before consuming it, and hfs_bnode_write() takes the length
as u32, so the negative value turns into a huge one. The copy then reads
data past the end of hip->cached_extents, which is only
sizeof(hfsplus_extent_rec) bytes long, and leaks kernel memory into the
image.
Reject an fd->entrylength that does not match sizeof(hfsplus_extent_rec) in
__hfsplus_ext_write_extent(), mirroring the check already performed in
__hfsplus_ext_read_extent().
Link: https://lore.kernel.org/lkml/cbd7003314c530d4f910eacf019ff80adad6687e.camel@dubeyko.com/
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/20260810092422.1691377-1-r772577952@gmail.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
|
|
A crafted HFS+ image can contain a corrupted B-tree node. The node
descriptor may contain a record count that does not fit in the node, and
record offsets may be unordered, unaligned, outside the node, or point into
the offset table itself.
Several B-tree helpers consume these on-disk fields before validating them:
hfs_bnode_dump() can walk past the offset table when num_recs is corrupted,
hfs_brec_lenoff() can produce an underflowed length or a record range that
overlaps the offset table. This can make the unlink/writeback path
repeatedly call hfs_bnode_read_u16() with invalid offsets while holding the
HFS+ B-tree lock, producing a flood of "requested invalid offset" messages.
Other writeback workers then block on tree->tree_lock and the system
reports tasks hung in hfsplus_write_inode().
Validate num_recs against the node size before walking the record offset
table. Reject record ranges that are unordered, unaligned, outside the
node, or overlapping the offset table. Reject invalid record indexes before
reading their offset entries, and avoid decrementing an already-zero
leaf_count.
Closes: https://lore.kernel.org/lkml/CANypQFb_2TqKGrztAXj5m0_v+QChxXDnQVeifzV8J25Vuju10Q@mail.gmail.com/
Assisted-by: Codex:gpt-5.5-xhigh
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Tested-by: Viacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/20260806073358.1184938-1-r772577952@gmail.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
|
|
Commit eb3b5bf1a88d ("PCI: Whitelist native hotplug ports for runtime D3"),
prevented native hotplug-capable Root Ports from entering D3 citing issues
on old Intel SkyLake Xeon-SP platform.
But there is no reason to restrict D3 for native hotplug-capable Root Ports
on non-x86 platforms. We recently enabled D3 on non hotplug-capable Root
Ports on non-x86 platforms (specifically for DT platforms) in commit
a5fb3ff63287 ("PCI: Allow PCI bridges to go to D3Hot on all non-x86"). So
do the same for native hotplug-capable Root Ports as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260729165005.896725-1-manivannan.sadhasivam@oss.qualcomm.com
|
|
read_exports() reports the offending line number when it fails to parse
Module.symvers. The counter is initialized to 1 but never incremented,
so every error blames line 1 regardless of where the bad line is.
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Song Liu <song@kernel.org>
Link: https://patch.msgid.link/133e16bb0c7cb916f10bbfb017eba525449ad1d6.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
EXPORT_SYMBOL_FOR_MODULES() puts a symbol in a "module:<names>"
namespace, which the module loader grants access to by matching the
importing module's name against that list.
klp_reloc_needed() only creates a klp reloc for module-owned exports; a
vmlinux export gets a normal reloc. For a vmlinux symbol exported with
EXPORT_SYMBOL_FOR_MODULES(), using a normal reloc results in a modpost
failure in klp-build:
ERROR: modpost: module livepatch-foo uses symbol mpol_shared_policy_lookup from namespace module:kvm, but does not import it.
And the modpost error is correct: even with that error removed, the
patch module would fail to load:
livepatch_foo: module uses symbol (mpol_shared_policy_lookup) from namespace module:kvm, but does not import it.
livepatch_foo: Unknown symbol mpol_shared_policy_lookup (err -22)
Treat it like an unexported symbol by using a klp reloc.
Note this only affects "module:" namespaces. Ordinary namespaced
exports continue to work with normal relocs thanks to copy_import_ns(),
which propagates the patched object's import_ns tags to the patch
module.
Fixes: dd590d4d57eb ("objtool/klp: Introduce klp diff subcommand for diffing object files")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://lore.kernel.org/6a6608f4-0a05-4d75-8b7f-edddfac9c5d4@redhat.com
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Song Liu <song@kernel.org>
Link: https://patch.msgid.link/fe5a00818e06ec613344d41d5944de054fcd8832.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
klp_reloc_needed() returns true for module exports to support
late-module patching. However, clone_reloc_klp() unconditionally
rejects symbols without a twin (i.e., new references added by the
patch), even when the symbol is a known export from Module.symvers.
Relax the check: allow new references to exported symbols by only
erroring on !twin when there is no export. The export metadata from
Module.symvers provides sufficient context to emit the klp-relocation
without a twin.
For a module export that isn't sufficient on its own though, as the
resulting klp relocation will only be resolved at patch-enable time if
the exporting module is loaded.
If the original (unpatched) module already depends on the exporting
module, the dependency is safe: the module loader ensures the dependency
is satisfied before the patched module can be loaded, so the
klp relocation target will exist.
However, if the patch introduces a reference to a module that the
original doesn't depend on, there is no such guarantee. The exporting
module could be absent or could be unloaded at any time, leading to a
relocation failure or use-after-free.
So also add a build-time check: when a new symbol reference (no twin)
targets a module export, verify that the original module already has at
least one UNDEF symbol resolving to that same exporting module. If not,
error out with a diagnostic message.
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/e0d725acb4774747f0e271308b4ca33daae2d5db.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
While cloning a reloc, klp diff calls find_export() to determine whether
the referenced symbol is exported. That decides whether the reference
needs a klp reloc, which object the klp symbol belongs to, and whether
the symbol's data needs to be copied into the patch module.
But find_export() matches purely on symbol name, so a static function or
variable which happens to share its name with an export is mistaken for
a reference to that export:
- klp_reloc_needed() creates a klp reloc pointing at the exporting
module's symbol rather than the local one. For a vmlinux export it
skips the klp reloc altogether, leaving a normal reloc which the
module loader resolves to the vmlinux symbol.
- clone_reloc() treats the symbol as external and clones it without
its data, leaving a dangling reference.
- validate_special_section_klp_reloc() attributes a static branch or
call key to the wrong module, and for a vmlinux export skips the
unsupported-key check entirely.
Exports are always global, so ignore local symbols in find_export().
Fixes: dd590d4d57eb ("objtool/klp: Introduce klp diff subcommand for diffing object files")
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/dafc7c017d1f62e2190a20dc84a52fbfc4c70210.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
A klp relocation section is .klp.rela.<objname>.<secname>, where objname
is the object being patched.
klp-build wrongly derives objname from where the referenced symbol
lives, not where it's referenced. For a cross-module reference like
patched can_isotp code calling can.ko's can_rx_unregister(), that gives
.klp.rela.can..text rather than .klp.rela.can_isotp..text. Unless the
patch happens to patch can.ko as well, the relocation never gets applied
and the call goes off into the weeds.
Name the intermediate section __klp_relocs.<objname> so post-link can
read the patched object's name from there.
Fixes: dd590d4d57eb ("objtool/klp: Introduce klp diff subcommand for diffing object files")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://lore.kernel.org/20260720145658.1103243-2-joe.lawrence@redhat.com
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/ee93a08f3e55e76ffa67d04e283917ddaa893f09.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
Explicitly disallow the patching and referencing of init code/data.
Otherwise it could potentially introduce some odd edge cases depending
on whether the target object's init section has been freed yet (note
that the init code still exists in the target module when doing late
module patching).
Such edge cases include sympos calculation and the patching and/or
referencing of non-existent (init-freed) code/data. Not to mention the
inherent differences in behavior that occur when the init code is only
patched *some* of the time depending on module loading order or kernel
config.
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Acked-by: Song Liu <song@kernel.org>
Link: https://patch.msgid.link/516e14f84cfbffa27dc19d3dcf35097504097966.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
In the error path of build_tree(), node instances can remain in the local
linked list when the function returns.
Whenever an invalid value is detected in the self ID sequence, each
allocated node instance is either an entry in the linked list or an
entry in the ports array of its parent node. Therefore, the allocate
node instances can be safely released by traversing the linked list from
its head.
Release the remaining node instances with for_each_fw_node() before
returning to the caller.
Fixes: 3038e353cfaf ("firewire: Add core firewire stack.")
Reported-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://lore.kernel.org/all/20260727095955.104972-1-nihaal@cse.iitm.ac.in/
Link: https://lore.kernel.org/r/20260811120928.700577-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
build_tree()
The node tree requires each child node to have exactly one port connected
to a parent node, while the root node must have no such port. This can be
validated by comparing the parent port count for a PHY with the rest of
the self ID sequence.
Currently, this validation is done after the node has been allocated. Move
it before the allocation so that an invalid self ID sequence can cause
an error without having to clean up the newly allocated node.
Link: https://lore.kernel.org/r/20260811120928.700577-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
The self ID sequence describes the state of each port for each PHY.
Currently, build_tree() counts the ports in two separate places.
Consolidate the port counting in one place.
Link: https://lore.kernel.org/r/20260811120928.700577-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
The UBI wear-leveling threshold (CONFIG_MTD_UBI_WL_THRESHOLD) is
currently a compile-time constant shared by all UBI devices. When a
single kernel image must support multiple NAND flashes with different
erase lifetimes, one global threshold cannot suit all devices.
Add a per-device configurable wl_threshold parameter:
- UAPI: add __s32 wl_threshold to struct ubi_attach_req, carved
from the existing padding.
- Module parameter: ubi.mtd gains a new optional token
"wl_threshold":
ubi.mtd=0,0,0,0,0,0,256 ubi.mtd=1,0,0,0,0,0,4096
0 means "use the kernel default", the accepted range is
2-65536.
Signed-off-by: Ran Hongyun <ranhongyun1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fix two issues introduced before:
- The parameter format string was missing the enable_fm and
need_resv_pool tokens introduced in an earlier commit.
- The bad-block reservation note was misplaced after Example 5
instead of after Example 3. It was misplaced due to an earlier patch.
Fixes: 83ff59a06663 ("UBI: support ubi_num on mtd.ubi command line")
Signed-off-by: Ran Hongyun <ranhongyun1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
In xlnx_formatter_pcm_open(), stream_data is allocated and
adata->play_stream or adata->capture_stream is assigned early. If a
later step, such as snd_pcm_hw_constraint_step() or
snd_pcm_hw_constraint_integer(), fails, the function returns the error
immediately. ALSA does not call the close callback when open fails, so
stream_data is leaked and the stream pointer is left dangling, pointing
to a substream that ALSA frees. A later interrupt would then call
snd_pcm_period_elapsed() on the freed substream.
Free stream_data and clear the stream pointer on the error paths.
Fixes: 6f6c3c36f091 ("ASoC: xlnx: add pcm formatter platform driver")
Assisted-by: opencode:deepseek-v4-flash-free
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260811185140.27149-1-rosenp@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ubi_detach_mtd_dev() obtains a device reference through ubi_get_device()
before checking whether the UBI device is busy. The busy return path drops
ubi->ref_count but leaves the device reference held, so the device object
cannot be released after a later detach.
Drop the device reference before returning -EBUSY.
Fixes: 7e84c961b2eb ("mtd: ubi: introduce pre-removal notification for UBI volumes")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
An x86 alternative with an empty replacement, e.g. the second entry of
ALTERNATIVE_2("orig", "repl", ft1, "", ft2)
has a replacementlen of zero. Its replacement offset still gets a
relocation, but the label it points at is the end of the previous
replacement, which is also the beginning of the *next* alternative's
replacement. The value is meaningless; get_alt_entry() already ignores
it for that reason.
klp diff doesn't ignore it. When such an alternative belongs to a
changed function, cloning its relocations drags in the unrelated
neighboring replacement, along with everything that replacement
references. On an x86 clang/lto build an empty alternative in
meminfo_proc_show() pulled in the replacement of an alternative in
proc_kcore_init(), silently emitting a klp relocation against init text
which has long since been freed by the time the patch is applied.
Add arch_alt_ignore_new_reloc() and skip such relocations when cloning.
This has to be arch specific: on arm64 a zero-length replacement instead
identifies an alternative callback, whose replacement offset points at
the callback function and must be preserved.
Fixes: dd590d4d57eb ("objtool/klp: Introduce klp diff subcommand for diffing object files")
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/7a885b70974795c3417f3358869e62aafd4ef783.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
create_fake_symbols() sizes each ANNOTATE_DATA_SPECIAL entry from the
offset of the next annotation, falling back to the end of the section
for the last entry. But the last entry is detected by a zero size,
which also happens for an *empty* entry: ALTERNATIVE(oldinstr, "", ft)
still annotates its zero-length replacement, at the same offset as the
next entry's annotation.
So every empty replacement gets a fake symbol spanning the entire rest
of .altinstr_replacement. That's harmless today only because
find_symbol_containing() picks the smaller of two overlapping symbols.
Track whether a next annotation was found rather than inferring it from
the size. A zero-length fake symbol is fine: find_symbol_containing()
skips those, so the properly sized symbol at the same offset still wins.
Fixes: dd590d4d57eb ("objtool/klp: Introduce klp diff subcommand for diffing object files")
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/913e691c5009397df832c7c9a18cd5cf71b42737.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
Testing klp-build with arm64 produced the following linker error during
the original kernel build:
`__notrim.1' referenced in section `.klp.symid' of vmlinux.o: defined in discarded section `.no_trim_symbol' of vmlinux.o
symbol_get() puts a static __notrim[] in .no_trim_symbol, which GCC
names __notrim.1, __notrim.2, etc. Two or more built-in translation
units calling symbol_get() thus produce duplicate names, resulting in
corresponding .klp.symid references which trigger the above error.
Add .no_trim_symbol to the discarded section list so its symbols don't
get symids.
Note this issue is not specific to arm64: it just needs two built-in
symbol_get() callers. arm64 trips over it easily because it has KVM
always compiled in vmlinux, whereas on x86 it's typically a module.
Fixes: 029223d30162 ("objtool/klp: Add .klp.symid for sympos disambiguation")
Acked-by: Song Liu <song@kernel.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Link: https://patch.msgid.link/5a3cc4cded743167dd0878220201d80f7e48e5d7.1786138493.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
|
|
ubi_init_attach() rolls back module initialization failures by scanning
ubi_devices[0..i-1], where i is the mtd= parameter index. That assumes
the parameter index matches the UBI device number.
That assumption is not true when mtd= specifies an explicit ubi_num. A
successfully attached device can be stored at a higher ubi_devices[]
slot, and a later failure can miss it during rollback.
Scan the full ubi_devices[] array and detach by the actual array index,
matching the way UBI devices are stored.
Fixes: 83ff59a06663 ("UBI: support ubi_num on mtd.ubi command line")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
ubifs_sb_verify_signature() bounds the on-disk ubifs_sig_node->len field
before handing the signature payload to verify_pkcs7_signature(), but the
check has the wrong sign:
if (le32_to_cpu(signode->len) > snod->len + sizeof(struct ubifs_sig_node))
The signature bytes start sizeof(struct ubifs_sig_node) (UBIFS_SIG_NODE_SZ,
64 bytes) into the node, so the payload is at most
snod->len - sizeof(struct ubifs_sig_node)
bytes long. Adding the header size instead of subtracting it accepts a
declared length up to 2 * UBIFS_SIG_NODE_SZ larger than the node actually
holds -- past the end of c->sbuf, which is vmalloc(c->leb_size).
verify_pkcs7_signature() -> pkcs7_parse_message() -> asn1_ber_decoder()
is then handed that inflated length and reads beyond the allocation while
walking the DER headers. The node length comes straight from the mounted
image, so a crafted signed UBIFS image reaches this via
ubifs_read_superblock() before the signature is cryptographically checked.
snod->len is guaranteed to be >= UBIFS_SIG_NODE_SZ by the node scanner
(c->ranges[UBIFS_SIG_NODE].min_len == UBIFS_SIG_NODE_SZ), so the corrected
subtraction cannot underflow. Legitimately signed images are unaffected: a
correct superblock never declares a signature longer than the node it is
embedded in.
Fixes: 817aa094842d ("ubifs: support offline signed images")
Cc: stable@vger.kernel.org
Signed-off-by: Ibrahim Hashimov <security@auditcode.ai>
Assisted-by: AuditCode-AI:2026.07
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Ning Ding says:
====================
bpf: Compare iterator types during state pruning
Iterator stack slots can be marked MEM_RCU or PTR_UNTRUSTED. The
STACK_ITER check in stacksafe() does not compare this type, so state
pruning can treat these states as equal and prune an unsafe path.
Compare the type and add a test where RCU protection has a gap.
---
Changes in v2:
- Convert the regression test to inline assembly so its verifier-sensitive
control-flow layout is stable.
- Add Eduard Zingerman's Acked-by tag to patch 1.
v1: https://lore.kernel.org/bpf/20260807004320.134069-1-dingning04@gmail.com/
====================
Link: https://patch.msgid.link/20260811035955.132989-1-dingning04@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
Add a path where RCU protection reaches zero and then starts again.
The iterator is untrusted after this gap and must be rejected.
Signed-off-by: Ning Ding <dingning04@gmail.com>
Link: https://patch.msgid.link/20260811035955.132989-3-dingning04@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
An iterator stack slot can be MEM_RCU or PTR_UNTRUSTED. These states
must not be equal, or the verifier can prune an unsafe path.
Compare the pointer type for STACK_ITER slots.
Fixes: dfab99df147b ("bpf: teach the verifier to enforce css_iter and task_iter in RCU CS")
Signed-off-by: Ning Ding <dingning04@gmail.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://patch.msgid.link/20260811035955.132989-2-dingning04@gmail.com
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
|
|
Convert the Texas Instruments OMAP L4 interconnect bus bindings
to DT schema.
During the conversion, several updates were made:
- Defined the compatible property as an array to require
the TI-specific string first, followed by either 'simple-bus' or
'simple-pm-bus'.
- Added a 'select' block to ensure this schema is only
applied to TI-specific nodes, preventing duplicate
schema warnings against the core simple-pm-bus.yaml.
- Added the L4 compatible strings used by the boards but missing from
the text binding, and corrected the 'ti,am3-l4-wkup' typo to
'ti,am33xx-l4-wkup'.
- Made 'reg' and 'reg-names' optional.
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Link: https://patch.msgid.link/20260810134051.380538-1-egbostina@gmail.com
[robh: move to bindings/bus/]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Convert the Texas Instruments SmartReflex bindings to DT schema.
Signed-off-by: Eduard Bostina <egbostina@gmail.com>
Link: https://patch.msgid.link/20260810131641.352391-1-egbostina@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Introduce devres-based helper for of_reserved_mem_device_init()
to help fight dangling references and ever so slightly reduce the
number of boilerplate deinitialization calls.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Link: https://patch.msgid.link/20260730073214.1146432-1-mukesh.ojha@oss.qualcomm.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Add compatible string for StarFive JHB100 plic.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://patch.msgid.link/20260806122553.182449-3-changhuang.liang@starfivetech.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
In ubi_update_fastmap(), when no fresh PEB is available to replace an
old fastmap PEB, the old PEB is reused by erasing it synchronously
via ubi_sync_erase() with the torture flag hardcoded to zero.
However, old_fm->to_be_tortured[] may be non-zero: it is set during
fastmap scanning when ubi_io_read_data()/ubi_io_read_ec_hdr() reports
UBI_IO_BITFLIPS, meaning the PEB showed signs of bit decay and should
be tortured to verify it is still reliable.
When the old PEB is instead returned to the WL sub-system via
ubi_wl_put_fm_peb(), the to_be_tortured flag is honored. The
synchronous reuse path is inconsistent: it silently skips the torture
test for PEBs that exhibited bit-flips.
Fix it by passing &old_fm->to_be_tortured[i] to ubi_sync_erase().
Fixes: dbb7d2a88d2a ("UBI: Add fastmap core")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
In __erase_worker(), when ubi_sync_erase() returns -EINTR, -ENOMEM,
-EAGAIN, or -EBUSY, the physical eraseblock is rescheduled for erasure
via schedule_erase() with the torture flag hardcoded to 0. This
unconditionally drops the torture request.
If the error occurred before torture_peb() completed (e.g., -ENOMEM
from the ec_hdr allocation in ubi_sync_erase(), errors from
self_check_not_bad()/nor_erase_prepare() in ubi_io_sync_erase(), or
torture_peb() failing mid-test because its internal do_sync_erase()/
ubi_io_read()/ubi_io_write() returned one of the above error codes),
the torture test was never finished. Such a PEB may reach the free
pool without being tortured, defeating the purpose of the torture
test for detecting marginally-bad eraseblocks.
If the error occurred after torture_peb() succeeded (the final
do_sync_erase() in ubi_io_sync_erase() or ubi_io_write_ec_hdr() in
ubi_sync_erase() failed), the torture has already been done and need
not be repeated.
Pass the torture flag by pointer to ubi_sync_erase() and
ubi_io_sync_erase(), and clear it to zero once torture_peb() has
completed successfully. __erase_worker() then forwards the updated
wl_wrk->torture to schedule_erase(): torture already done is dropped,
torture not completed is preserved across the reschedule.
Fixes: 784c145444e7 ("UBI: fix error handling in erase worker")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
That flag exists to stop gas emulating instructions the assembler thinks
the target lacks. It is a gas-only option, and LLVM's integrated
assembler does not emulate instructions in the first place, so nothing
is needed there.
Condition it on CONFIG_AS_IS_GNU rather than the compiler, so it is
still passed for clang builds using GNU as (LLVM_IAS=0) and omitted only
for the integrated assembler.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260805185557.3283233-1-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
do_entInt() opens with local_irq_disable(), which with
CONFIG_TRACE_IRQFLAGS only calls trace_hardirqs_off() if interrupts were
not already off:
#define local_irq_disable() \
do { \
bool was_disabled = raw_irqs_disabled();\
raw_local_irq_disable(); \
if (!was_disabled) \
trace_hardirqs_off(); \
} while (0)
On alpha raw_irqs_disabled() is (rdps() & 7) == IPL_MAX, i.e. IPL 7.
PALcode raises PS.IPL to the level of the interrupt before entInt runs,
so for an IPL 7 entry - a processor machine check (vector 0x660) or a
system event (vector 0x680), both IPL_MCHECK == IPL_MAX - the gate is
already true and the annotation is skipped. lockdep keeps whatever
hardirq state the interrupted context had. If that context had
interrupts enabled, lockdep believes they are still enabled for the
duration of the handler, and every lockdep_assert_irqs_disabled() in the
interrupt path fires:
WARNING: kernel/context_tracking.c:346 at ct_irq_enter+0xc4/0xd0, CPU#0: swapper/0/0
[...]
[<fffffc0001ef74d4>] ct_irq_enter+0xc4/0xd0
[<fffffc000105ebd0>] irq_enter+0x20/0x50
[<fffffc000103707c>] do_entInt+0x1dc/0x2e0
[<fffffc0001031d60>] ret_from_exception+0x0/0x10
irq event stamp: 735356346
hardirqs last enabled at (735356346): trace_hardirqs_on+0x68/0x220
hardirqs last disabled at (735356345): do_idle+0xf0/0x270
The stamps show the problem directly: the most recent event is the
enable from the interrupted idle loop, and do_entInt() recorded no
disable at all. ct_irq_exit() warns the same way on the way out.
Ordinary device interrupts arrive at IPL 3-5 and IPIs and performance
counter interrupts at IPL 6, so was_disabled is false for them and the
annotation happens normally. Only the two IPL 7 vectors are affected,
which is why this needs an environmental event to show up.
Take the hardware IPL out of the decision and drive the annotation from
lockdep's own state instead.
This corrects the annotation only. An IPL 7 event can also interrupt a
region that has legitimately disabled interrupts, where irq_enter() and
irq_exit() are not the right primitives and NMI semantics are needed;
that is a larger change and is left alone here.
Tested on an AlphaServer ES47 (Marvel/EV7) by injecting system events
through the system management path: fifteen injections, idle and under
load, with no splat. The same injection on a freshly booted kernel
without this change reproduces both warnings.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Tested-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260810202835.3592833-2-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
On Marvel the CMOS clock is only reachable from the boot cpu, so
remote_read_time() and remote_set_time() bounce the access there with
smp_call_function_single(), whose callback runs in hard interrupt
context.
alpha_rtc_read_time() calls mc146818_get_time() with a 10 ms timeout.
That waits out the RTC update cycle in mc146818_avoid_UIP(), which drops
rtc_lock and udelay()s 100 us at a time until the update completes or
the timeout expires:
for (i = 0; UIP_RECHECK_LOOPS_MS(i) < timeout; i++) {
spin_lock_irqsave(&rtc_lock, flags);
...
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
spin_unlock_irqrestore(&rtc_lock, flags);
udelay(UIP_RECHECK_DELAY);
continue;
}
So a clock read from a non-boot cpu can spin for up to 10 ms in hard
interrupt context on the boot cpu, while the cpu that sent the request
spins in smp_call_function_single() waiting for it to finish.
mc146818_set_time() does not poll, but it takes rtc_lock too, and
rtc_lock is a spinlock_t. Only raw spinlocks may be taken in hard
interrupt context, so lockdep reports the write path as soon as a
non-boot cpu sets the clock:
[ BUG: Invalid wait context ]
-----------------------------
swapper/0/0 is trying to lock:
fffffc0003690470 (rtc_lock){....}-{3:3}, at: mc146818_set_time+0x74/0x450
other info that might help us debug this:
context-{2:2}
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 7.2.0-rc1 #1 NONE
Trace:
[<fffffc000102ebb0>] dump_stack+0x28/0x44
[<fffffc000110efcc>] __lock_acquire+0xb0c/0x1060
[<fffffc000110f5f0>] lock_acquire.part.0+0xd0/0x300
[...]
[<fffffc0001b0d834>] mc146818_set_time+0x74/0x450
[<fffffc0001f090cc>] _raw_spin_lock_irqsave+0x7c/0xc0
[<fffffc0001042f90>] do_remote_set+0x90/0xc0
[<fffffc000119c1a4>] __flush_smp_call_function_queue+0x314/0x5c0
[<fffffc000119c474>] generic_smp_call_function_single_interrupt+0x24/0x40
[<fffffc000103d984>] handle_ipi+0xa4/0x230
[<fffffc0001037044>] do_entInt+0x1a4/0x2e0
The rtc class ops are always called from process context, so there is no
reason to run the access from an interrupt at all. Use work_on_cpu() to
run it in a worker on the boot cpu. Alpha does not support cpu hotplug,
so the boot cpu cannot go offline while the work is pending.
Tested on an AlphaServer ES47 (Marvel/EV7): hwclock read and write
pinned to a non-boot cpu, twenty times, with no splat.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Magnus Lindholm <linmag7@gmail.com>
Link: https://lore.kernel.org/r/20260810202835.3592833-1-mattst88@gmail.com
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
|
|
Md Sadre Alam <md.alam@oss.qualcomm.com> says:
The Qualcomm QPIC SPI-NAND controller supports both single (x1) and
quad (x4) transfer modes, however the current driver operates only in
single-bit mode. This series adds support for quad data transfers and
includes a vendor-specific fix required for Macronix SPI-NAND devices.
Link: https://patch.msgid.link/20260807-quad-v2-0-8ec821e2f22b@oss.qualcomm.com
|
|
Macronix SPI-NAND devices use opcode 0x6b for quad output cache reads,
while most other devices use opcode 0xeb. The QPIC SPI-NAND driver does
not currently recognize opcode 0x6b, causing read operations to fail
when Macronix devices select this cache read variant.
Add the Macronix-specific read opcode to the command mapping logic and
treat it the same as the existing quad read operations.
This allows Macronix SPI-NAND devices to operate correctly in quad read
mode.
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260807-quad-v2-3-8ec821e2f22b@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for quad (x4) transfer mode in the QPIC SPI NAND driver.
The controller supports both single (x1) and quad (x4) SPI transfers,
but the driver currently operates only in x1 mode.
Track the QUAD enable state from the device configuration register
(0xB0) and switch the data transfer width accordingly. When the core
enables quad mode, use x4 transfers for read and program operations to
improve throughput.
Introduce a quad_mode flag in struct qpic_spi_nand to cache the current
device state. The flag is updated based on GET_FEATURE responses from
the configuration register.
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260807-quad-v2-2-8ec821e2f22b@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move qcom_spi_cmd_mapping() above qcom_spi_read_page() so it can be
used by read path changes added in a subsequent patch.
No functional change.
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
Link: https://patch.msgid.link/20260807-quad-v2-1-8ec821e2f22b@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
