| Age | Commit message (Collapse) | Author |
|---|
|
Troy Mitchell <troy.mitchell@linux.spacemit.com> says:
On some SoCs (e.g. SpacemiT K3), multiple I2S controllers share the
same physical BCLK. When one controller is already streaming, the
others must use hw_params that result in the same BCLK rate, otherwise
the shared clock would be reconfigured and corrupt the active stream.
This series adds framework-level support for this constraint:
Patch 1 adds the dt-bindings for the spacemit,k3-i2s compatible.
The K3 SoC uses the same I2S IP as K1 but requires additional clocks:
a dedicated sysclk_div, along with c_sysclk and c_bclk which are
shared across multiple I2S controllers.
Patch 2 adds a DEFINE_GUARD wrapping snd_soc_card_mutex_lock() and
snd_soc_card_mutex_unlock() so that scope-based locking picks up the
SND_SOC_CARD_CLASS_RUNTIME lockdep subclass.
Patch 3 adds the constraint logic in soc-pcm.c. During PCM open,
every DAI that has a bclk clock pointer gets a hw_rule registered
unconditionally. The rule callback runs at hw_refine time: it scans
the card for an active peer sharing the same physical BCLK (via
clk_is_match()) that has already completed hw_params, then constrains
the current stream's rate to match the established BCLK rate. The
first DAI to complete hw_params is unconstrained; subsequent DAIs
must match. Two modes are supported:
- Default (I2S): BCLK = rate * channels * sample_bits. The rule
derives the valid rate range from the current channel and
sample_bits intervals.
- Explicit ratio (TDM): if the driver sets dai->bclk_ratio
(e.g. slots * slot_width), the rule computes the single valid
rate as active_bclk_rate / bclk_ratio.
This series was prompted by review feedback on the SpacemiT K3 I2S
series, where a vendor-specific fixed-sample-rate property was rejected
in favor of a generic framework solution:
https://lore.kernel.org/all/afFqgF6ZRwYdfUmL@sirena.co.uk/
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-0-a71a86faaa20@linux.spacemit.com
|
|
Add a bclk field to struct snd_soc_dai and a helper function
snd_soc_dai_set_bclk_clk() that platform drivers can use to declare
which clock is their BCLK.
Also cache the bclk_ratio in snd_soc_dai_set_bclk_ratio() so that
the framework can use it later in hw_rule evaluation for TDM
configurations where BCLK = rate * slots * slot_width.
When multiple DAIs on the same card share the same physical BCLK
(detected via clk_is_match()), the ASoC core can automatically
constrain their hw_params so that the resulting BCLK rates are
compatible. This commit adds the data structure support; the actual
constraint logic follows in the next patch.
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://patch.msgid.link/20260522-i2s-same-blk-v4-1-a71a86faaa20@linux.spacemit.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drivers were accessing this drm_exec member directly.
While that may seem harmless, it will require action if
the drm_exec utility is made a subclass of a dma-resv transaction
utility as outlined in the cover-letter.
Provide an accessor, drm_exec_ticket() to avoid that.
v2:
- Fix amdgpu compile error (Intel CI)
- Update the commit message.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-5-thomas.hellstrom@linux.intel.com
|
|
The xe driver was using the drm_exec retry pointer directly to
restart the locking loop after out-of-memory errors. This is
relying on undocumented behaviour.
Instead add a drm_exec_retry() macro that can be used in this
situation, and that also warns if the struct drm_exec is
not newly (re-)initialized.
Use that macro in xe.
v2:
- Only allow if the drm_exec context is newly initialized.
(Christian)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-4-thomas.hellstrom@linux.intel.com
|
|
Use __UNIQUE_ID as done elsewhere in the kernel rather than a
hand-rolled __PASTE to craft a unique id.
Also use __maybe_unused rather than (void) to signify that a
variable, althrough written to, may not actually be used.
v2:
- Move assignment to declaration (Christian)
- Declare the retry pointer as void *const.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-3-thomas.hellstrom@linux.intel.com
|
|
Nobody makes any use of it. Possible internal future users can
instead use the _index variable. External users shouldn't use
it since the array it's pointing into is internal drm_exec state.
v2:
- Use a unique id for the loop variable (Christian)
Assisted-by: GitHub Copilot:claude-sonnet-4.6
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patch.msgid.link/20260520101616.41284-2-thomas.hellstrom@linux.intel.com
|
|
Prior to commit 57c31e6d620f ("ACPI: scan: Use acpi_setup_gpe_for_wake()
for buttons"), ACPI button wakeup GPEs having handler methods remained
enabled after acpi_wakeup_gpe_init(), but currently they are not enabled
because acpi_setup_gpe_for_wake() disables them.
That causes function keys to stop working on some systems [1] and there
may be other related issues elsewhere.
To address that, make the ACPI button driver enable wakeup GPEs for ACPI
buttons so long as they have handler methods. While this does not
restore the old behavior exactly (the ACPI button driver needs to be
bound to the button devices for the GPEs to be enabled), it should be
sufficient to restore the missing functionality.
For this purpose, introduce acpi_enable_gpe_cond() that enables
a GPE if its dispatch type matches the supplied one and modify
acpi_button_probe() to use that function for enabling the GPEs in
question.
Fixes: 57c31e6d620f ("ACPI: scan: Use acpi_setup_gpe_for_wake() for buttons")
Reported-by: Nick <nick@kousu.ca>
Closes: https://lore.kernel.org/linux-acpi/E2OXET.4X5GTP37VTNC3@kousu.ca/ [1]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Nick <nick@kousu.ca>
Cc: 7.0+ <stable@vger.kernel.org> # 7.0+
Link: https://patch.msgid.link/9629117.CDJkKcVGEf@rafael.j.wysocki
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We need the driver-core fixes in here as well to build on top of.
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
|
|
Neil Armstrong <neil.armstrong@linaro.org> says:
Add support for the SG Micro SGM3804 Single Inductor Dual Output
Buck/Boost Converter used to power LCD panels a provide positive
and negative power rails with configurable voltage and active
discharge function for each output.
The SGM3804 is powered by the enable GPIO pins inputs and only
supports I2C write messages.
In order to add flexibility and simplify the driver, the
regmap cache is enabled and populated with default values
since we can't write registers when the 2 GPIOs are down.
This regulator is used to provide vsn and vsn power to the
Ayaneo Pocket S2 dual-DSI LCD panel.
Link: https://patch.msgid.link/20260522-topic-sm8650-ayaneo-pocket-s2-sgm3804-v5-0-bd6b1c300ecc@linaro.org
|
|
This feature is required to use 32bit arp/ip/ip6/ebtables binaries on
64bit kernels. I don't think there are many users left.
Support has been a compile-time option since 2021 and defaults to off
since 2023.
The XTABLES_COMPAT config option is already off in many distributions
including Debian and Fedora.
Give a few more months before complete removal but disable support in
user namespaces already.
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Pull bpf fixes from Alexei Starovoitov:
- Fix bpf_throw() and global subprog combination (Kumar Kartikeya
Dwivedi)
- Fix out of bounds access in BPF interpreter (Yazhou Tang)
- Fix potential out of bounds access in inner per-cpu array map
(Guannan Wang)
- Reject NULL data/sig in bpf_verify_pkcs7_signature (KP Singh)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
libbpf: fix off-by-one in emit_signature_match jump offset
bpf: Reject NULL data/sig in bpf_verify_pkcs7_signature
selftests/bpf: Cover global subprog exception leaks
bpf: Check global subprog exception paths
bpf: make bpf_session_is_return() reference optional
bpf: Use array_map_meta_equal for percpu array inner map replacement
selftests/bpf: Add test for large offset bpf-to-bpf call
bpf: Fix s16 truncation for large bpf-to-bpf call offsets
bpf: Fix out-of-bounds read in bpf_patch_call_args()
|
|
The driver supports a new comp_mask: REQ_MASK_FIXED_QUE_ATTR.
The application sets this comp_mask bit in the CREATE_QP ureq
to indicate direct control of the QP. The driver goes through
the required processing for app allocated QPs (previous patches).
Only variable WQE mode is supported for these QPs.
This patch removes an unused comp_mask:
BNXT_RE_QP_REQ_MASK_VAR_WQE_SQ_SLOTS
Link: https://patch.msgid.link/r/20260519150041.7251-10-sriharsha.basavapatna@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
App allocated QPs can use a separate doorbell for each QP.
This doorbell region can be passed through a new driver specific
DBR_HANDLE attribute, during QP creation. When this attribute
is set, associate the QP with the given doorbell region.
While the QP holds a reference to the dbr, the dbr itself
cannot be destroyed and is rejected with EBUSY error.
Link: https://patch.msgid.link/r/20260519150041.7251-9-sriharsha.basavapatna@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
For app allocated QPs, the driver shouldn't use slots/round-up logic
to compute the msn table size. The application handles this logic
and computes 'sq_npsn' and passes it to the driver using a new uapi
parameter.
Link: https://patch.msgid.link/r/20260519150041.7251-5-sriharsha.basavapatna@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
This commit documents the rcu_access_pointer() use case for fetching the
old value of an RCU-protected pointer within a lockless updater for use
by an atomic cmpxchg() operation.
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reported-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
|
|
s/srcu_read_lock_safe()/srcu_read_lock_fast_updown(), there being no
such thing as srcu_read_lock_safe().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
|
|
This new torture_sched_set_normal() function clamps the nice value at
the MIN_NICE..MAX_NICE limits, splatting it these limits are exceeded.
It then invokes sched_set_normal() to set the new value. This prevents
more difficult-to-debug failures within the scheduler.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fixes from Danilo Krummrich:
- Remove the software node on platform device release(); without this,
the software node remains registered after the device is gone and a
subsequent platform_device_register_full() reusing the same node
fails with -EBUSY
- In sysfs_update_group(), do not remove a pre-existing directory when
create_files() fails; the previous code would silently destroy a
sysfs group that the caller did not create
- Set fwnode->secondary to NULL in fwnode_init() to avoid dereferencing
uninitialized memory (e.g. in dev_to_swnode()) when the firmware node
is allocated on the stack or via a non-zeroing allocator
* tag 'driver-core-7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
device property: set fwnode->secondary to NULL in fwnode_init()
sysfs: don't remove existing directory on update failure
driver core: platform: remove software node on release()
|
|
Pull rdma fixes from Jason Gunthorpe:
- syzbot triggred crash in rxe due to concurrent plug/unplug
- Possible non-zero'd memory exposed to userspace in bnxt_re
- Malicous 'magic packet' with SIW causes a buffer overflow
- Tighten the new uAPI validation code to not crash in debugging prints
and have the right module dependencies in drivers
- mana was missing the max_msg_sz report to userspace
- UAF in rtrs on an error path
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rtrs: Fix use-after-free in path file creation cleanup
RDMA/mana_ib: Report max_msg_sz in mana_ib_query_port
RDMA/core: Do not read wild stack memory in uverbs_get_handler_fn()
RDMA/core: Move the _ib_copy_validate_udata* functions to ib_core_uverbs
RDMA/siw: Reject MPA FPDU length underflow before signed receive math
RDMA/bnxt_re: zero shared page before exposing to userspace
selftests/rdma: explicitly skip tests when required modules are missing
RDMA/nldev: Add mutual exclusion in nldev_dellink()
|
|
suspend
Per PCIe v7.0, sec 5.5.3.3.1, when exiting L1.2 due to an endpoint
asserting CLKREQ# signal, the REFCLK must be turned on within the latency
advertised in the LTR message. This requirement applies to L1.1 as well.
On some platforms like Qcom, these requirements are satisfied during OS
runtime, but not while resuming from the system suspend. This happens
because the PCIe RC driver may remove all resource votes and turn off the
PHY analog circuitry during suspend to maximize power savings while keeping
the link in L1SS.
Consequently, when the endpoint asserts CLKREQ# to wake up, the RC driver
must restore the PHY and enable the REFCLK. When this recovery process
exceeds the L1SS exit latency time (roughly L10_REFCLK_ON + T_COMMONMODE),
the endpoint may treat it as a fatal condition and trigger Link Down (LDn).
This results in a reset that destroys the internal device state.
So to indicate this platform limitation to the client drivers, introduce a
new flag 'pci_host_bridge::broken_l1ss_resume' and check it in
pci_suspend_retains_context(). If the flag is set by the RC driver, the API
will return 'false' indicating the client drivers that the device context
may not be retained and the drivers must be prepared for context loss.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260519-l1ss-fix-v2-2-b2c3a4bdeb15@oss.qualcomm.com
|
|
The dtlk driver supports the RC Systems DoubleTalk PC ISA speech
synthesizer card. It has severe coding style issues and has only
received tree-wide fixes and drive-by cleanups in the entire Git
history (since Linux 2.6.12-rc2). The same hardware is supported by
drivers/accessibility/speakup for screen reader use, but that
implementation does not share any code with this driver. Given all of
these factors, it is likely the driver is entirely unused. Remove it to
reduce future maintenance workload.
Note: The removed maintainer is already listed in CREDITS.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260502043341.34324-1-enelsonmoore@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
during suspend
Currently, PCI endpoint drivers (e.g. nvme) use pm_suspend_via_firmware()
to check whether device state is preserved during system suspend. If
firmware will be invoked at the end of suspend, we don't know whether
devices will retain their internal state.
But device context might be lost due to platform issues as well. Having
those checks in endpoint drivers will not scale and will cause a lot of
code duplication.
Add pci_suspend_retains_context() as a sole point of truth that the
endpoint drivers can rely on to check whether they can expect the device
context to be retained or not.
If pci_suspend_retains_context() returns 'false', drivers need to prepare
for context loss by performing actions such as resetting the device, saving
the context, shutting it down etc. If it returns 'true', drivers do not
need to perform any special action and can leave the device in active
state.
Right now, this API only incorporates pm_suspend_via_firmware(), but will
be extended in future commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260519-l1ss-fix-v2-1-b2c3a4bdeb15@oss.qualcomm.com
|
|
struct bpf_arena is opaque to callers outside arena.c. Add two helpers
for struct_ops subsystems that need to reach into an arena:
bpf_arena_map_kern_vm_start(struct bpf_map *map)
returns @map's kern_vm_start. A sched_ext follow-up needs this
to translate kern_va <-> uaddr.
bpf_prog_arena(struct bpf_prog *prog)
returns the bpf_map of the arena referenced by @prog (NULL if
@prog references no arena). The verifier enforces at most one
arena per program. Used by struct_ops callers that auto-discover
an arena from a member prog and need to take a map reference.
Suggested-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Link: https://lore.kernel.org/r/20260522172219.1423324-6-tj@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add a helper that walks the member progs of the struct_ops map
containing a given @kdata vmtable. struct_ops ->reg() callbacks (and
similar) sometimes need to inspect the loaded BPF programs, e.g. to
discover maps they reference via prog->aux->used_maps.
The implementation mirrors bpf_struct_ops_id(): container_of @kdata
to recover the bpf_struct_ops_map, then iterate st_map->links[i]->prog
for i in [0, funcs_cnt). Same access pattern, no new locking - by the
time ->reg() fires st_map is fully populated and stable.
A sched_ext follow-up walks the member progs of a cid-form scheduler's
struct_ops map, reads prog->aux->arena directly, and requires all member
progs to reference exactly one arena, without requiring the BPF program
to call a registration kfunc.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Link: https://lore.kernel.org/r/20260522172219.1423324-5-tj@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The existing kernel-side export of bpf_arena_alloc_pages is _non_sleepable
only - it's used by the verifier to inline the kfunc when the call site is
non-sleepable. There is no sleepable equivalent for kernel callers. The
kfunc bpf_arena_alloc_pages itself is BPF-only.
sched_ext needs sleepable kernel-side allocs for its arena pool init/grow
paths. Add bpf_arena_alloc_pages_sleepable() mirroring the _non_sleepable
wrapper but passing sleepable=true to arena_alloc_pages().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Link: https://lore.kernel.org/r/20260522172219.1423324-4-tj@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
BPF arena usage is becoming more prevalent, but kernel <-> BPF communication
over arena memory is awkward today. Data has to be staged through a trusted
kernel pointer with extra code and copying on the BPF side. While reads
through arena pointers can use a fault-safe helper, writes don't have a good
solution. The in-line alternative would need instruction emulation or asm
fixup labels.
Enable direct kernel-side reads and writes within GUARD_SZ / 2 of any
handed-in arena pointer, without bounds checking. A per-arena scratch page
is installed by the arch fault path into empty arena kernel PTEs - x86 from
page_fault_oops() for not-present faults, arm64 from __do_kernel_fault() for
translation faults, both after the existing exception-table and KFENCE
handling. The faulting instruction retries and the access is also reported
through the program's BPF stream, preserving error reporting.
bpf_prog_find_from_stack() resolves the current BPF program (and its arena)
from the kernel stack - no new bpf_run_ctx state is added. Recovery covers
the 4 GiB arena plus the upper half-guard (GUARD_SZ / 2). The lower
half-guard is excluded because well-behaved kfuncs only access forward from
arena pointers. The kfunc-author contract - access at most GUARD_SZ / 2 past
a handed-in pointer - is documented in Documentation/bpf/kfuncs.rst.
The install is lock-free via ptep_try_set(). On race-loss the winning
installer's PTE is already valid, so the access retry succeeds. The arena
clear path uses ptep_get_and_clear() so installer and clearer race through
atomic accessors. No flush_tlb_kernel_range() afterwards. Stale "not mapped"
entries just cause one extra re-fault, cheaper than a global IPI on every
install.
Scratch exists only to keep the kernel from oopsing on an in-line arena
access. Its presence at a PTE means the BPF program has already
malfunctioned, and the violation is reported through the program's BPF
stream. The only requirement for behavior on a scratched PTE is that the
kernel doesn't crash. In particular, any user-side access through such a PTE
may segfault. The shared scratch page is freed once during map destruction.
BPF instruction faults continue to use the existing JIT exception-table
path. This patch changes only the kernel-text fault path. No UAPI flag is
added. The new behavior is the default.
v2: Use ptep_get_and_clear() in apply_range_clear_cb(). (David)
v3: Stub bpf_arena_handle_page_fault() for !CONFIG_BPF_SYSCALL. (lkp)
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Cc: David Hildenbrand <david@kernel.org>
Link: https://lore.kernel.org/r/20260522172219.1423324-3-tj@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add ptep_try_set(ptep, new_pte): atomically set *ptep to new_pte iff it is
currently pte_none(). Returns true on success, false if the slot was already
populated or the arch has no implementation.
The intended caller is the upcoming bpf_arena kernel-side fault recovery
path. The install runs from a page fault that can be nested under locks
held by the faulting kernel caller (e.g. a BPF program holding
raw_res_spin_lock_irqsave on its arena's spinlock), so trylock-and-retry
would A-A deadlock. Lock-free cmpxchg is the only viable option, which
constrains this helper to special kernel page tables where concurrent
writers cooperate via atomic accessors.
The generic version in <linux/pgtable.h> returns false. x86 and arm64
override with try_cmpxchg-based implementations on the underlying pteval.
Other architectures get the false stub - the callers there already fall
through to oops.
v2: Rename to ptep_try_set(). Tighten kerneldoc. (David, Alexei)
v3: Note that strict-zero cmpxchg is narrower than pte_none(). (Andrea)
Suggested-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Cc: David Hildenbrand <david@kernel.org>
Acked-by: David Hildenbrand (arm) <david@kernel.org>
Link: https://lore.kernel.org/r/20260522172219.1423324-2-tj@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v7.2
- Save/restore more registers during suspend/resume on the RZ/G2L and
RZ/V2H SoC families,
- Add support for the RZ/G3L (R9A08G046) SoC,
- Add support for pinconf-groups in debugfs on EMMA Mobile,
SH/R-Mobile, R-Car, RZ/G1, and RZ/G2 SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linusw@kernel.org>
|
|
Currently the vendor, model, and revision members of struct scsi_device
are pointers to fixed-length strings that are not NUL-terminated.
Fixed-precision format specifiers (e.g., "%.8s") are required whenever
they are printed and strncmp() must be used to compare these fields.
This is error-prone.
Convert these fields to fixed-size character arrays within struct
scsi_device. Remove an !sdev->model check because sdev->model is now
guaranteed not to be NULL.
This patch fixes a bug in the qla2xxx driver. It makes the following
code safe:
if (state_flags & BIT_4)
scmd_printk(KERN_WARNING, cp,
"Unsupported device '%s' found.\n",
cp->device->vendor);
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Brian Bunker <brian@purestorage.com>
Link: https://patch.msgid.link/20260515205222.1754621-4-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move three constants from target/target_core_base.h into
scsi/scsi_common.h. Add three new constants in the scsi_common.h header
file. This patch prepares for using these constants in the SCSI core.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Brian Bunker <brian@purestorage.com>
Link: https://patch.msgid.link/20260515205222.1754621-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a quirk to support TX Equalization Training (EQTR) using Adapt
L0L1L2L3 length which is larger than what is allowed by M-PHY spec ver
6.0.
Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Ziqi Chen <ziqi.chen@oss.qualcomm.com>
Link: https://patch.msgid.link/20260501131641.826258-2-can.guo@oss.qualcomm.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We plan to no longer hold RTNL in "ip link show", and use RCU instead.
Assume rtnl_fill_dpll_pin() will have to fill DPLL_A_PIN_ID.
It is fine to over-estimate skb size (by 8 bytes) in if_nlmsg_size().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20260521171440.114956-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers might have error messages to propagate to user space. Propagate
the netlink extack so that they can inform user space in a verbal way of
their limitations.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20260521010320.208138-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two rstat fixes:
- Out-of-bounds access in the css_rstat_updated() BPF kfunc when
called with an unchecked user-supplied cpu
- Over-strict NMI guard after the recent switch to try_cmpxchg left
sparc and ppc64 unable to queue rstat updates from NMI"
* tag 'cgroup-for-7.1-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: rstat: relax NMI guard after switch to try_cmpxchg
cgroup/rstat: validate cpu before css_rstat_cpu() access
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes pull, amdgpu/xe being the usual, with bonus msm content
to bulk things out, otherwise it has the usual scattered changes, with
amdxdna dropping a badly thought out userspace api.
gem:
- clean up LRU locking
msm:
- Core:
- Fixed bindings for SM8650, SM8750 and Eliza
- Don't use UTS_RELEASE directly
- Fix typo in clock-names property
- DPU:
- Fixed CWB description on Kaanapali
- Fixed scanline strides for YUV UBWC formats
- Stopped DSI register dumping to access past the end of region
- DSI:
- Fix dumping unaligned regions
- GPU:
- Fix GMEM_BASE for a6xx gen3
- Fix userspace reachable crash on a2xx-a4xx
- Fix sysprof_active for counter collection with IFPC enabled GPUs
- Fix shrinker lockdep
amdgpu:
- Userq fixes
- VPE fix
- SMU 15 fix
- Misc fixes
- VCE fixes
- DC bios parsing fixes
- DC aux fix
- Mode1 reset fix
- RAS fixes
amdkfd:
- Misc fixes
radeon:
- CS parser fix
xe:
- SRIOV related fixes
- Fix leak and double-free
- Multi-cast register fixes
- Multi-queue fix
i915:
- Fix joiner color pipeline selection [display]
- Fix readback for target_rr in Adaptive Sync SDP [dp]
- Apply Intel DPCD workaround when SDP on prior line used [psr]
amdxdna:
- remove mmap and export for ubuf
bridge:
- chipone-icn6211: managed bridge cleanup
- lt66121: acquire reset GPIO
- megachips: fix clean up on failed IRQ requests
v3d:
- fix UAF in error code paths
- release GEM-object ref on free'd jobs
virtio:
- use uninterruptible resv locking in plane updates
mediatek:
- fix sparse warnings"
* tag 'drm-fixes-2026-05-23' of https://gitlab.freedesktop.org/drm/kernel: (78 commits)
drm/xe/oa: Fix exec_queue leak on width check in stream open
drm/virtio: use uninterruptible resv lock for plane updates
drm/amdgpu: fix handling in amdgpu_userq_create
drm/radeon/evergreen_cs: Add missing NULL prefix check in surface check
drm/amdgpu: userq_va_mapped should remain true once done
drm/amdgpu: avoid integer overflow in VA range check
drm/amd/ras: Fix UMC error address allocation leak
drm/amdgpu: unmap all user mappings of framebuffer and doorbell before mode1 reset
drm/amd/display: Validate payload length and link_index in dc_process_dmub_aux_transfer_async
drm/amd/display: Validate GPIO pin LUT table size before iterating
drm/amd/display: Fix integer overflow in bios_get_image()
drm/amdkfd: Check bounds for allocate_sdma_queue restore_sdma_id
drm/amdgpu: use atomic operation to achieve lockless serialization
drm/amdkfd: Check bounds on allocate_doorbell
drm/amdgpu/vce3: Fix VCE 3 firmware size and offsets
drm/amdgpu/vce2: Fix VCE 2 firmware size and offsets
drm/amdgpu/vce1: Stop using amdgpu_vce_resume
drm/amdgpu/vce1: Fix VCE 1 firmware size and offsets
drm/amdgpu/vce1: Don't repeat GTT MGR node allocation
drm/amdgpu/vce1: Check if VRAM address is lower than GART.
...
|
|
Add debugfs entries to expose hardware configuration and diagnostic
information that aids in debugging driver initialization and runtime
operations without adding noise to dmesg.
The debugfs directory for each PCI device is named using pci_name()
(the unique BDF address), and its creation and removal is integrated
into mana_gd_setup() and mana_gd_cleanup_device() respectively, so
that all callers (probe, remove, suspend, resume, shutdown) share a
single code path.
Device-level entries (under /sys/kernel/debug/mana/<BDF>/):
- num_msix_usable, max_num_queues: Max resources from hardware
- gdma_protocol_ver, pf_cap_flags1: VF version negotiation results
- num_vports, bm_hostmode: Device configuration
Per-vPort entries (under /sys/kernel/debug/mana/<BDF>/vportN/):
- port_handle: Hardware vPort handle
- max_sq, max_rq: Max queues from vPort config
- indir_table_sz: Indirection table size
- steer_rx, steer_rss, steer_update_tab, steer_cqe_coalescing:
Last applied steering configuration parameters
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260519064621.772154-1-ernis@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers setting CPUFREQ_NEED_UPDATE_LIMITS expect target() to be
invoked even if the target frequency remains unchanged, so they can
update their internal policy limits state.
Currently the core invokes target() unconditionally whenever the
requested frequency matches policy->cur for such drivers, even if
policy->min and policy->max haven't changed since the previous update.
Track pending policy limit updates explicitly and skip redundant
target() invocations when neither the target frequency nor the
effective limits changed.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Reviewed-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Link: https://patch.msgid.link/d0107c364b709abca21acf88072220bc05478594.1779423281.git.viresh.kumar@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Replace "diver" with "driver" in the comment describing
CPUFREQ_NEED_UPDATE_LIMITS.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Reviewed-by: Lifeng Zheng <zhenglifeng1@huawei.com>
Link: https://patch.msgid.link/396f64411431ffbb5b4f07d1f2e0bbf9763d468f.1779423281.git.viresh.kumar@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The current implementation uses pci_num_vf() while holding the
memory_lock to prevent changing the power state of a PF when
VFs are enabled. This creates a lockdep circular dependency
warning because memory_lock is held during device probing.
[ 286.997167] ======================================================
[ 287.003363] WARNING: possible circular locking dependency detected
[ 287.009562] 7.0.0-dbg-DEV #3 Tainted: G S
[ 287.015074] ------------------------------------------------------
[ 287.021270] vfio_pci_sriov_/18636 is trying to acquire lock:
[ 287.026942] ff45bea2294d4968 (&vdev->memory_lock){+.+.}-{4:4}, at:
vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.036530]
[ 287.036530] but task is already holding lock:
[ 287.042383] ff45bea3a96b8230 (&new_dev_set->lock){+.+.}-{4:4}, at:
vfio_group_fops_unl_ioctl+0x44d/0x7b0
[ 287.051879]
[ 287.051879] which lock already depends on the new lock.
[ 287.051879]
[ 287.060070]
[ 287.060070] the existing dependency chain (in reverse order) is:
[ 287.067568]
[ 287.067568] -> #2 (&new_dev_set->lock){+.+.}-{4:4}:
[ 287.073941] __mutex_lock+0x92/0xb80
[ 287.078058] vfio_assign_device_set+0x66/0x1b0
[ 287.083042] vfio_pci_core_register_device+0xd1/0x2a0
[ 287.088638] vfio_pci_probe+0xd2/0x100
[ 287.092933] local_pci_probe_callback+0x4d/0xa0
[ 287.098001] process_scheduled_works+0x2ca/0x680
[ 287.103158] worker_thread+0x1e8/0x2f0
[ 287.107452] kthread+0x10c/0x140
[ 287.111230] ret_from_fork+0x18e/0x360
[ 287.115519] ret_from_fork_asm+0x1a/0x30
[ 287.119983]
[ 287.119983] -> #1 ((work_completion)(&arg.work)){+.+.}-{0:0}:
[ 287.127219] __flush_work+0x345/0x490
[ 287.131429] pci_device_probe+0x2e3/0x490
[ 287.135979] really_probe+0x1f9/0x4e0
[ 287.140180] __driver_probe_device+0x77/0x100
[ 287.145079] driver_probe_device+0x1e/0x110
[ 287.149803] __device_attach_driver+0xe3/0x170
[ 287.154789] bus_for_each_drv+0x125/0x150
[ 287.159346] __device_attach+0xca/0x1a0
[ 287.163720] device_initial_probe+0x34/0x50
[ 287.168445] pci_bus_add_device+0x6e/0x90
[ 287.172995] pci_iov_add_virtfn+0x3c9/0x3e0
[ 287.177719] sriov_add_vfs+0x2c/0x60
[ 287.181838] sriov_enable+0x306/0x4a0
[ 287.186038] vfio_pci_core_sriov_configure+0x184/0x220
[ 287.191715] sriov_numvfs_store+0xd9/0x1c0
[ 287.196351] kernfs_fop_write_iter+0x13f/0x1d0
[ 287.201338] vfs_write+0x2be/0x3b0
[ 287.205286] ksys_write+0x73/0x100
[ 287.209233] do_syscall_64+0x14d/0x750
[ 287.213529] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 287.219120]
[ 287.219120] -> #0 (&vdev->memory_lock){+.+.}-{4:4}:
[ 287.225491] __lock_acquire+0x14c6/0x2800
[ 287.230048] lock_acquire+0xd3/0x2f0
[ 287.234168] down_write+0x3a/0xc0
[ 287.238019] vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.243436] __rpm_callback+0x8c/0x310
[ 287.247730] rpm_resume+0x529/0x6f0
[ 287.251765] __pm_runtime_resume+0x68/0x90
[ 287.256402] vfio_pci_core_enable+0x44/0x310
[ 287.261216] vfio_pci_open_device+0x1c/0x80
[ 287.265947] vfio_df_open+0x10f/0x150
[ 287.270148] vfio_group_fops_unl_ioctl+0x4a4/0x7b0
[ 287.275476] __se_sys_ioctl+0x71/0xc0
[ 287.279679] do_syscall_64+0x14d/0x750
[ 287.283975] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 287.289559]
[ 287.289559] other info that might help us debug this:
[ 287.289559]
[ 287.297582] Chain exists of:
[ 287.297582] &vdev->memory_lock --> (work_completion)(&arg.work)
--> &new_dev_set->lock
[ 287.297582]
[ 287.310023] Possible unsafe locking scenario:
[ 287.310023]
[ 287.315961] CPU0 CPU1
[ 287.320510] ---- ----
[ 287.325059] lock(&new_dev_set->lock);
[ 287.328917]
lock((work_completion)(&arg.work));
[ 287.336153] lock(&new_dev_set->lock);
[ 287.342523] lock(&vdev->memory_lock);
[ 287.346382]
[ 287.346382] *** DEADLOCK ***
[ 287.346382]
[ 287.352315] 2 locks held by vfio_pci_sriov_/18636:
[ 287.357125] #0: ff45bea208ed3e18 (&group->group_lock){+.+.}-{4:4},
at: vfio_group_fops_unl_ioctl+0x3e3/0x7b0
[ 287.367048] #1: ff45bea3a96b8230 (&new_dev_set->lock){+.+.}-{4:4},
at: vfio_group_fops_unl_ioctl+0x44d/0x7b0
[ 287.376976]
[ 287.376976] stack backtrace:
[ 287.381353] CPU: 191 UID: 0 PID: 18636 Comm: vfio_pci_sriov_
Tainted: G S 7.0.0-dbg-DEV #3 PREEMPTLAZY
[ 287.381355] Tainted: [S]=CPU_OUT_OF_SPEC
[ 287.381356] Call Trace:
[ 287.381357] <TASK>
[ 287.381358] dump_stack_lvl+0x54/0x70
[ 287.381361] print_circular_bug+0x2e1/0x300
[ 287.381363] check_noncircular+0xf9/0x120
[ 287.381364] ? __lock_acquire+0x5b4/0x2800
[ 287.381366] __lock_acquire+0x14c6/0x2800
[ 287.381368] ? pci_mmcfg_read+0x4f/0x220
[ 287.381370] ? pci_mmcfg_write+0x57/0x220
[ 287.381371] ? lock_acquire+0xd3/0x2f0
[ 287.381373] ? pci_mmcfg_write+0x57/0x220
[ 287.381374] ? lock_release+0xef/0x360
[ 287.381376] ? vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.381377] lock_acquire+0xd3/0x2f0
[ 287.381378] ? vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.381379] ? lock_is_held_type+0x76/0x100
[ 287.381382] down_write+0x3a/0xc0
[ 287.381382] ? vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.381383] vfio_pci_core_runtime_resume+0x1f/0xa0
[ 287.381384] ? __pfx_pci_pm_runtime_resume+0x10/0x10
[ 287.381385] __rpm_callback+0x8c/0x310
[ 287.381386] ? ktime_get_mono_fast_ns+0x3d/0xb0
[ 287.381389] ? __pfx_pci_pm_runtime_resume+0x10/0x10
[ 287.381390] rpm_resume+0x529/0x6f0
[ 287.381392] ? lock_is_held_type+0x76/0x100
[ 287.381394] __pm_runtime_resume+0x68/0x90
[ 287.381396] vfio_pci_core_enable+0x44/0x310
[ 287.381398] vfio_pci_open_device+0x1c/0x80
[ 287.381399] vfio_df_open+0x10f/0x150
[ 287.381401] vfio_group_fops_unl_ioctl+0x4a4/0x7b0
[ 287.381402] __se_sys_ioctl+0x71/0xc0
[ 287.381404] do_syscall_64+0x14d/0x750
[ 287.381405] ? entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 287.381406] ? trace_irq_disable+0x25/0xd0
[ 287.381409] entry_SYSCALL_64_after_hwframe+0x77/0x7f
Introduce a private flag 'sriov_active' in the vfio_pci_core_device
struct. This allows the driver to track the SR-IOV power state requirement
without relying on pci_num_vf() while holding the memory_lock. The lock is
now only held to set the flag and ensure the device is in D0, after which
pci_enable_sriov() can be called without the lock.
Fixes: f4162eb1e2fc ("vfio/pci: Change the PF power state to D0 before enabling VFs")
Cc: stable@vger.kernel.org
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Suggested-by: Alex Williamson <alex@shazbot.org>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Link: https://lore.kernel.org/r/20260514173449.3282188-1-rananta@google.com
[promote bitfield to plain bool to avoid storage-unit races]
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Use IOMEM_ERR_PTR() when returning a void __iomem * rather than
ERR_PTR(). This fixes a sparse warning, "different address spaces".
Fixes: 859dc0f6253b ("vfio/pci: Replace vfio_pci_core_setup_barmap() with vfio_pci_core_get_iomap()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202605211601.U1OvmuqY-lkp@intel.com/
Signed-off-by: Matt Evans <mattev@meta.com>
Link: https://lore.kernel.org/r/20260522124215.3268565-1-mattev@meta.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
|
|
Add blk_rq_has_data(), an analogue of bio_has_data() for struct request.
This skips one dereference relative to bio_has_data(rq->bio).
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Link: https://patch.msgid.link/20260513211846.1956810-2-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The UX500 crypto drivers were removed in commit 453de3eb08c4
("crypto: ux500/cryp - delete driver") and commit dd7b7972cb89
("crypto: ux500/hash - delete driver"). No file includes
this header.
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: Costa Shulyupin <costa.shul@redhat.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Allow device attribute to reside in read-only memory.
Both const and non-const attributes are handled by the utility macros
and attributes can be migrated one-by-one.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20260512-sysfs-const-attr-device_attr-prep-v3-4-cb7c17b34d52@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The constification of device attributes will require a transition phase,
where 'struct device_attribute' contains a classic non-const and a new
const variant of the 'show' and 'store' callbacks.
As __ATTR() and friends can not handle this duplication stop using them.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20260512-sysfs-const-attr-device_attr-prep-v3-3-cb7c17b34d52@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the upcoming constification of device attributes the generic
__ATTR() macros are insufficient.
Prepare for a split by introducing new low-level macros specific to
device attributes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20260512-sysfs-const-attr-device_attr-prep-v3-2-cb7c17b34d52@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This macro is unused and would create extra work during the upcoming
constification of device attributes. Remove it.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://patch.msgid.link/20260512-sysfs-const-attr-device_attr-prep-v3-1-cb7c17b34d52@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When an overlay is applied, if the target device has already probed
successfully and bound to a device, then some of the fw_devlink logic
that ran when the device was probed needs to be rerun. This allows newly
created dangling consumers of the overlayed device tree nodes to be
moved to become consumers of the target device.
[Herve: Add the call to driver_deferred_probe_trigger()]
[Herve: Use fwnode_test_flag() to test fwnode flags value]
Fixes: 1a50d9403fb9 ("treewide: Fix probing of devices in DT overlays")
Reported-by: Herve Codina <herve.codina@bootlin.com>
Closes: https://lore.kernel.org/lkml/CAMuHMdXEnSD4rRJ-o90x4OprUacN_rJgyo8x6=9F9rZ+-KzjOg@mail.gmail.com/
Closes: https://lore.kernel.org/all/20240221095137.616d2aaa@bootlin.com/
Closes: https://lore.kernel.org/lkml/20240312151835.29ef62a0@bootlin.com/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/lkml/20240411235623.1260061-3-saravanak@google.com/
[Herve: Rebase on top of recent kernel]
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Tested-by: Kalle Niemi <kaleposti@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260511155755.34428-3-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Constify the groups arrays, allowing to assign constant arrays.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/42624513-923c-4970-834d-036282e24e24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Constify the groups arrays, allowing to assign constant arrays.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/265f6584-8edd-48a0-9568-a9d584b9ec3a@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
