summaryrefslogtreecommitdiff
path: root/drivers/bluetooth/btusb.c
AgeCommit message (Collapse)Author
5 daysBluetooth: btusb: Fix leaked runtime PM reference in btusb_resetJiajia Liu
btusb_reset calls usb_autopm_get_interface to resume the device before queuing a reset of it, but never calls the matching usb_autopm_put_interface. usb_queue_reset_device ends up in usb_reset_device(), and since btusb provides no pre_reset/post_reset callbacks the interface is merely unbound and rebound: the interface device object survives this cycle, and so does its PM usage count, which is not cleared when the driver is unbound. As a result every reset permanently leaks a PM usage reference, preventing the interface from being runtime suspended again until it is unbound. Set BTUSB_RESET flag before usb_queue_reset_device so that btusb_disconnect drops the reference. If the flag is already set, drop one reference. Fixes: c9209b269afd ("Bluetooth: btusb: Introduce generic USB reset") Assisted-by: Claude:qwen3.8-max Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
5 daysBluetooth: btusb: mediatek: Fix leaked runtime PM reference in resetJiajia Liu
MT7925 on HP Pro Mini 260 sometimes timed out during reloading driver and reset usb device. btusb_suspend is not called again after closing bluetooth interface. usbcore: registered new interface driver btusb Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20260605184935 Bluetooth: hci0: Execution of wmt command timed out Bluetooth: hci0: Failed to send wmt patch dwnld (-110) Bluetooth: hci0: Failed to set up firmware (-110) usb 3-10: reset high-speed USB device number 4 using xhci_hcd Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20260605184935 Bluetooth: hci0: Device setup in 1856545 usecs Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: hci0: AOSP quality report is supported Bluetooth: MGMT ver 1.23 btusb_mtk_reset calls usb_autopm_get_interface to resume the device before driving the hardware reset, but never calls the matching usb_autopm_put_interface. Every hardware reset therefore leaks a PM usage reference of the interface, preventing the device from being runtime suspended again until it is unbound. Add the BTUSB_RESET flag. It is set before usb_queue_reset_device and is cleared in btusb_disconnect, which drops the reference as well. If the flag is already set when a new reset is requested, drop one reference. Also clear BTMTK_HW_RESET_ACTIVE if usb_autopm_get_interface fails, otherwise no further reset could ever be attempted. Fixes: 25b6d7593a3a ("Bluetooth: btmtk: introduce btmtk reset work") Assisted-by: Claude:qwen3.8-max Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
5 daysBluetooth: btusb: Fix UAF of btusb_data by rx_workLuiz Augusto von Dentz
btusb_close() and btusb_flush() cancel data->rx_work with the asynchronous cancel_delayed_work(), so if btusb_rx_work() is already running on another CPU it keeps running after the cancel returns. btusb_disconnect() calls hci_unregister_dev(), which invokes btusb_close(), and then frees the btusb_data. A still running btusb_rx_work() then dereferences the freed data: while ((skb = skb_dequeue(&data->acl_q))) data->recv_acl(data->hdev, skb); Use cancel_delayed_work_sync() instead. In btusb_close() the cancel also has to happen after btusb_stop_traffic(), otherwise an URB completion racing with the cancel can requeue the work right after it has been waited for. Fixes: 800fe5ec302e ("Bluetooth: btusb: Add support for queuing during polling interval") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
5 daysBluetooth: Properly disable remote wakeup for MT7922/MT7925 on Ryzen platformRong Zhang
It is reported that a remote wakeup could cause MT7922/MT7925's btusb interface completely unresponsive. Resetting the xHCI root hub doesn't help at all, and recovering from such a state needs a power cycle. All reports seen to be relevant to Ryzen-based laptops. These NICs are usually used as OEM components thanks to some sort of reference designs. Their popularity on other platforms is unclear. While there is still a chance that the quirk may exist on other platforms, be cautious and only apply the quirk to direct children of Ryzen platforms's root hubs for the time being. In most cases the root hub is on the SoC or PCH, which needs the quirk. Unfortunately, this can't distinguish root hubs on PCIe add-in cards. Such roughness should be acceptable, as PCIe USB controller add-in cards are less commonly used nowadays. On the other hand, applying the quirk doesn't hurt any functionalities either, as the device can still be used as a wakeup source if desired. Theoretically, we could retrieve the root hub's PCI vendor ID with some hierarchy magic, but that's too intrusive... Meanwhile, though device_set_wakeup_capable(false) is the correct fix for other NICs with fake remote wakeup capabilities, doing so for MT7922/MT7925 effectively prevents it from being used as wakeup sources as per userspace requests. Hence, return -EBUSY on runtime suspend to prevent the interface from being autosuspended while it's still opened, which has the same effect as device_set_wakeup_capable(false), since disabling remote wakeup simply causes the USB core to gate runtime autosuspend as well due to needs_remote_wakeup == 1. The interface can be safely autosuspended as long as remote wakeup is disabled, i.e., after closing the HCI device. Specifically, the interface may still take the advantage of remote wakeup in order to wake up the system from sleep if userspace has enabled it as a wakeup source. Fixes: e31d761628ad ("Bluetooth: btmtk: Disable remote wakeup for MT7922/MT7925") Tested-by: Rafael Passos <rafael@rcpassos.me> Signed-off-by: Rong Zhang <i@rong.moe> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-24Bluetooth: btusb: limit RTL8761B BROKEN_EXT_SCAN quirk to 0bda:a728Junjie Cao
Commit 5ead2063611a ("Bluetooth: btrtl: fix RTL8761B/BU broken LE extended scan") set HCI_QUIRK_BROKEN_EXT_SCAN for every CHIP_ID_8761B device to cure repeated 0x2042 failures on an 0bda:a728 dongle. The brokenness is per-dongle, not per-chip: on a TP-Link UB500 (2357:0604, RTL8761BU, fw 0xdfc6d922) extended scan works, and the legacy scan path the quirk forces is what is broken -- LE Set Scan Enable (0x200c) times out with -110 about 30 s after firmware load, btusb resets the device, and the adapter re-enumerates in an endless loop (382 firmware reloads in one boot). 7.1.8, which predates the stable backport, runs clean on this unit; 7.1.9 loops. Move the quirk from btrtl's chip-wide switch to a btusb device-table flag on the USB id the original fix was verified against. Other 8761B dongles return to their earlier long-standing behaviour. Link: https://bugzilla.redhat.com/show_bug.cgi?id=2521504 Fixes: 5ead2063611a ("Bluetooth: btrtl: fix RTL8761B/BU broken LE extended scan") Cc: stable@vger.kernel.org Signed-off-by: Junjie Cao <junjie.cao@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Simplify btusb_recv_bulk() by hci_acl_dlen()Zijun Hu
Simplify btusb_recv_bulk() by using hci_acl_dlen() instead of: __le16 dlen = hci_acl_hdr(skb)->dlen; ... __le16_to_cpu(dlen) ... Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add a simple static btusb_prepare_reset()Zijun Hu
Add btusb_prepare_reset() to do cleanup before a reset, and apply it to btusb_mtk_reset() as well. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Make btusb_recv_{event,acl}() take struct hci_dev *Zijun Hu
Both helpers currently take struct btusb_data *, which is private to btusb.c, as parameter type as below: int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb) int btusb_recv_acl(struct btusb_data *data, struct sk_buff *skb) To allow vendor USB-transport-specific source files to share them as well, change the type to struct hci_dev *. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Realtek: Replace HCI_VENDOR_PKT usage with HCI_EV_VENDORZijun Hu
The macros below have different meanings even though they share the same value 0xff: HCI_VENDOR_PKT: HCI packet indicator or type HCI_EV_VENDOR: event code of a VSE This usage of HCI_VENDOR_PKT is wrongly checking an event code. Fix by using HCI_EV_VENDOR for event code. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: QCA: Replace HCI_VENDOR_PKT usages with HCI_EV_VENDORZijun Hu
The macros below have different meanings even though they share the same value 0xff: HCI_VENDOR_PKT: HCI packet indicator or type HCI_EV_VENDOR: event code of a VSE These usages of HCI_VENDOR_PKT are wrongly checking an event code. Fix by using HCI_EV_VENDOR for event code. Also fix warning "CHECK: Unnecessary parentheses around comparison" given by checkpatch.pl. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add support for 1357:c123 Realtek 8852BE devicePavel Zverev
Wiko Hi MateBook 14 Ryzen 200 laptops (DMI system-product-name "MNCA-XX", board "M1060") are equipped with an RTL8852BE Wi-Fi/BT combo chip (rtw89_8852be), whose Bluetooth radio enumerates as 1357:c123 instead of one of the already-supported 1358:c123 / 0bda:c123 identifiers, presumably due to OEM rebranding. Without a matching entry it only matches the generic USB Bluetooth class fallback, so the Realtek firmware/config (rtl8852btu_fw.bin / rtl8852btu_config.bin) is never loaded and the adapter cannot discover or connect to any device, even though hciconfig reports it as powered and scanning. Device descriptor: idVendor 0x1357 idProduct 0xc123 bcdDevice 0.00 iManufacturer 1 Realtek iProduct 2 Bluetooth Radio bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth Adding the same BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH quirk already used for 1358:c123 and 0bda:c123 fixes firmware loading and normal operation. Signed-off-by: Pavel Zverev <playximik29@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add ASUS USB-BT600 for Realtek 8761CUChristoph Zwerschke
Add the vendor/product ID (0x0b05, 0x1d70) to the usb_device_id table for the Realtek RTL8761CU-based ASUS USB-BT600 adapter. It binds via the generic Bluetooth class today, so BTUSB_REALTEK is never set and the rtl8761cu firmware is not loaded, leaving the controller non-functional. With the entry the driver loads rtl_bt/rtl8761cu_fw.bin (already shipped by linux-firmware) and the adapter works (tested: A2DP and ASHA). Similar to commit bc597f0cc44f ("Bluetooth: btusb: Add TP-Link UB600 for Realtek 8761BUV"). Device info from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 23 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=1d70 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Controller C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Cc: stable@vger.kernel.org Signed-off-by: Christoph Zwerschke <cito@online.de> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add ASUS USB-BT540 for Realtek 8761CUChristoph Zwerschke
Add the vendor/product ID (0x0b05, 0x1bef) to the usb_device_id table for the Realtek RTL8761CU-based ASUS USB-BT540 adapter. It binds via the generic Bluetooth class today, so BTUSB_REALTEK is never set and the rtl8761cu firmware is not loaded, leaving the controller non-functional. With the entry the driver loads rtl_bt/rtl8761cu_fw.bin (already shipped by linux-firmware) and the adapter works (tested: A2DP and ASHA). Similar to commit bc597f0cc44f ("Bluetooth: btusb: Add TP-Link UB600 for Realtek 8761BUV"). Device info from /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 22 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=1bef Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Controller C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Cc: stable@vger.kernel.org Signed-off-by: Christoph Zwerschke <cito@online.de> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add IMC Networks QCA9377 to quirks tableTibor Harcsa
Add the USB ID (13d3:3503) for the IMC Networks Qualcomm Atheros QCA9377 Bluetooth controller to the btusb quirks table. This device requires Qualcomm Rome firmware and wideband speech support to function properly; otherwise, BLE scanning fails with HCI unexpected event opcode 0x2005 errors. The device reports the following in /sys/kernel/debug/usb/devices: P: Vendor=13d3 ProdID=3503 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Tibor Harcsa <silurust@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Use & instead of == to test bitflag BTUSB_IGNOREZijun Hu
The driver_info field is a bitmask, so use & instead of == to test the BTUSB_IGNORE bitflag against it, which is consistent with how the other flags are tested. Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Reduce a redundant assignment in btusb_probe()Zijun Hu
Initialize @priv_size at declaration rather than separately: - Simpler: one statement completes both declaration and assignment. - More flexible: the variable is immediately usable from that point, so any new priv_size += can be freely inserted without caring about where the separate priv_size = 0 sits. Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Simplify btusb_shutdown_qca() by using __hci_reset_sync()Zijun Hu
btusb_shutdown_qca() open-codes a synchronous raw HCI reset that is functionally equivalent to the newly added __hci_reset_sync(). Replace it with __hci_reset_sync() and return its result directly. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: QCA: move qca_dump out of struct btusb_dataZijun Hu
'struct btusb_data' ideally should not include vendor specific fields, but it currently includes the QCA devcoredump member 'struct qca_dump_info qca_dump'. Fix by moving it into hci_dev private area accessed by hci_get_priv(). Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: QCA: Fix populating devcoredump fields on unenabled devicesZijun Hu
Devcoredump is not enabled for ATH3012 or QCA_ROME, but they unconditionally populate devcoredump fields in btusb_setup_qca(). Fix by populating devcoredump fields only when BTUSB_QCA_WCN6855 is set, which marks the first generation of QCA BT SoCs for which devcoredump is enabled. Fixes: 20981ce2d5a5 ("Bluetooth: btusb: Add WCN6855 devcoredump support") Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Record matched usb_device_id into btusb_dataZijun Hu
Add @match_id to btusb_data to record the matched usb_device_id which will be used later. Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Fix BD_ADDR byte order in btusb_set_bdaddr_wcn6855()Zijun Hu
btusb_set_bdaddr_wcn6855() sends the address without swapping byte order for VSC 0xFC14, but the command expects the address in reversed byte order compared to other HCI commands like HCI_Create_Connection, resulting in a wrong BD_ADDR being set. btmon log on WCN6855 shows VSC 0xFC14 is sent with swapped bytes 11 22 33 44 55 66, and Read BD ADDR returns the expected address 11:22:33:44:55:66: < HCI Command: Vendor (0x3f|0x0014) plen 6 #3 [hci0] 11 22 33 44 55 66 > HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] Vendor (0x3f|0x0014) ncmd 1 Status: Success (0x00) < HCI Command: Read BD ADDR (0x04|0x0009) plen 0 #11 [hci0] > HCI Event: Command Complete (0x0e) plen 10 #12 [hci0] Read BD ADDR (0x04|0x0009) ncmd 1 Status: Success (0x00) Address: 11:22:33:44:55:66 (OUI 11-22-33) Fix by swapping the input address before issuing the command. Fixes: b40f58b97386 ("Bluetooth: btusb: Add Qualcomm Bluetooth SoC WCN6855 support") Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add USB ID 13d3:3625 for MediaTek MT7922Gustavo Evgucci
The IMC Networks MT7922 Bluetooth adapter with USB ID 13d3:3625 is not recognized as a MediaTek device because it is missing from the btusb device ID table. As a result, btmtk firmware loading is never triggered and the HCI reset command times out with -ETIMEDOUT. Add the device with BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH flags, consistent with the neighboring 13d3:3627, 13d3:3628 and 13d3:3630 entries which use the same chip. Tested on: MediaTek MT7922 (Wi-Fi 6E combo card, IMC Networks BT USB interface), kernel 7.0.11-arch1-1. /sys/kernel/debug/usb/devices: T: Bus=01 Lev=01 Prnt=01 Port=12 Cnt=03 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3625 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Gustavo Evgucci <monesss315@gmail.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-08-07Bluetooth: btusb: Add new VID/PID 0x0489/0xe156 for MT7902Sean Wang
Add VID 0489 & PID e156 for MediaTek MT7902 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=09 Cnt=05 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e156 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Co-developed-by: Kirill Shubin <kirill.kz.902@gmail.com> Signed-off-by: Kirill Shubin <kirill.kz.902@gmail.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-07-28Bluetooth: btusb: Fix short read errors in btusb_qca_send_vendor_req()Greg Kroah-Hartman
If btusb_qca_send_vendor_req() gets a "short" read from a device, it will accidentally treat that as a "real" read and populate the returned value with some unknown and probably totally invalid data. Fix this logic error up by calling usb_control_msg_recv() which guarantees a "full" read happens, and then simplify the error checking for when btusb_qca_send_vendor_req() is called. Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-07-20Bluetooth: btusb: validate Realtek vendor event lengthPengpeng Hou
btusb_recv_event_realtek() reads the event code at data[0] and the Realtek subevent code at data[2] before deciding whether to consume a vendor event as a coredump. For example, the two-byte event ff 00 contains a complete vendor-event header declaring zero parameters. The old classifier still reads a nonexistent third byte and can misclassify the event as a coredump if the adjacent byte is 0x34. Require the HCI event header and first parameter to be present before inspecting the Realtek subevent code. Short events continue through the normal HCI receive path, which owns their protocol validation. Fixes: 044014ce85a1 ("Bluetooth: btrtl: Add Realtek devcoredump support") Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: clean up probe error handlingJohan Hovold
Clean up probe error handling by using dedicated error labels with an "err" prefix. Note that the endpoint lookup helper returns -ENXIO when endpoints are missing which is functionally equivalent to returning -ENODEV. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: fix wakeup irq devres lifetimeJohan Hovold
The OOB wakeup interrupt is device managed but its lifetime is incorrectly tied to the child HCI device rather than the USB interface to which the driver is bound. This should not cause any trouble currently as the interrupt will be disabled when the HCI device is deregistered on disconnect (but this was not always the case, see [1]), and there should be no further references if probe fails before registering it. But it is still technically wrong as the reference counted HCI device could in theory remain after a probe failure. Explicitly free the interrupt on disconnect so that it is guaranteed to be disabled before freeing the (non-managed) driver data (including if disconnected while suspended). [1] 699fb50d9903 ("drivers: base: Free devm resources when unregistering a device") Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support") Cc: Rajat Jain <rajatja@google.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: fix wakeup source leak on probe failureJohan Hovold
Make sure to disable wakeup on probe failure to avoid leaking the wakeup source. Fixes: fd913ef7ce61 ("Bluetooth: btusb: Add out-of-band wakeup support") Cc: stable@vger.kernel.org # 4.11 Cc: Rajat Jain <rajatja@google.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: fix use-after-free on marvell probe failureJohan Hovold
Make sure to stop any TX URBs submitted during Marvell OOB wakeup configuration on later probe failures to avoid use-after-free in the completion callback. This issue was reported by Sashiko while reviewing a fix for a wakeup source leak in the btusb probe errors paths. Link: https://sashiko.dev/#/patchset/20260402092704.2346710-1-johan%40kernel.org Fixes: a4ccc9e33d2f ("Bluetooth: btusb: Configure Marvell to use one of the pins for oob wakeup") Cc: stable@vger.kernel.org # 4.11 Cc: Rajat Jain <rajatja@google.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: fix use-after-free on registration failureJohan Hovold
Make sure to release the sibling interfaces in case controller registration fails to avoid use-after-free and double-free when they are eventually disconnected. This issue was reported by Sashiko while reviewing a fix for a wakeup source leak in the btusb probe errors paths. Link: https://sashiko.dev/#/patchset/20260402092704.2346710-1-johan%40kernel.org Fixes: 9bfa35fe422c ("[Bluetooth] Add SCO support to btusb driver") Fixes: 9d08f50401ac ("Bluetooth: btusb: Add support for Broadcom LM_DIAG interface") Cc: stable@vger.kernel.org # 2.6.27 Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add support for TP-Link TL-UB250Cris
Add USB ID 2357:0607 for TP-Link TL-UB250. This is a Realtek RTL8761BUV based Bluetooth adapter. Without this entry the device is picked up by the generic Bluetooth USB class match and exposes hci0, but the Realtek setup path is not used and rtl8761bu firmware/config are not loaded. The controller reports Realtek Semiconductor Corporation as the manufacturer and LMP subversion 0x8761. With this entry added, btusb loads rtl_bt/rtl8761bu_fw.bin and rtl_bt/rtl8761bu_config.bin successfully. Relevant part of /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=06 Port=00 Cnt=01 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2357 ProdID=0607 Rev= 2.00 S: Product=TP-Link TL-UB250 Adapter C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Use the same flags as the existing TP-Link 2357:0604 entry. Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Cris <cxs1494089474@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add TP-Link UB600 for Realtek 8761BUVNils Helmig
Add the vendor/product ID (0x37ad, 0x0600) to usb_device_id table for Realtek 8761BUV. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=37ad ProdID=0600 Rev= 2.00 S: Manufacturer= S: Product=TP-Link Bluetooth USB Adapter S: SerialNumber=ACA7F14FD2A5 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Nils Helmig <nils.helmig@web.de> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add USB ID 2c4e:0128 for Mercusys MA60XNBZenm Chen
Add USB ID 2c4e:0128 for Mercusys MA60XNB, an RTL8851BU-based Wi-Fi + Bluetooth adapter. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c4e ProdID=0128 Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org # 6.6.x Signed-off-by: Zenm Chen <zenmchen@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add support for Intel Lizard Peak 2 (0x8087:0x0040)Ravindra
Device from /sys/kernel/debug/usb/devices: T: Bus=09 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0040 Rev= 0.00 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Ravindra <ravindra@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: MT7925: Add VID/PID 13d3/3609luke-yj.chen
Add VID 13d3 & PID 3609 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3609 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: luke-yj.chen <luke-yj.chen@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add Realtek RTL8922AE VID/PID 0bda/d923Chen Zhang
Add the vendor/product ID (0x0bda, 0xd923) to usb_device_id table for Realtek RTL8922AE. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=10 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=d923 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C885A01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Chen Zhang <zhangchen01@kylinos.cn> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add Realtek RTL8922AE VID/PID 0bda/d922Chen Zhang
Add the vendor/product ID (0x0bda, 0xd922) to usb_device_id table for Realtek RTL8922AE. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=10 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=d922 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C885A01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Chen Zhang <zhangchen01@kylinos.cn> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: Add Mercusys MA530 for Realtek RTL8761BUVHrvoje Nuic
Add the USB ID for the Mercusys MA530 Bluetooth adapter. The device uses a Realtek RTL8761BUV controller and works with the existing Realtek setup path. The device reports vendor ID 0x2c4e and product ID 0x0115, and loads the rtl_bt/rtl8761bu_fw.bin firmware successfully with this quirk. Signed-off-by: Hrvoje Nuic <hrvoje.nuic@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btmtk: add event filter to filter specific eventChris Lu
Add an event filter to filter event with specific opcode to prevent BT stack from receiving unexpected event. Event with opcode 0xfc5d is generated when MediaTek's Bluetooth enable firmware logs and is not expected to be sent to userspace. Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: MT7925: Add VID/PID 0e8d/8c38Chris Lu
Add VID 0e8d & PID 8c38 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=8c38 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-06-11Bluetooth: btusb: MT7922: Add VID/PID 0e8d/223cChris Lu
Add VID 0e8d & PID 223c for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=223c Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-05-27Bluetooth: btusb: Allow firmware re-download when version matchesShuai Zhang
The Bluetooth host decides whether to download firmware by reading the controller firmware download completion flag and firmware version information. If a USB error occurs during the firmware download process (for example due to a USB disconnect), the download is aborted immediately. An incomplete firmware transfer does not cause the controller to set the download completion flag, but the firmware version information may be updated at an early stage of the download process. In this case, after USB reconnection, the host attempts to re-download the firmware because the download completion flag is not set. However, since the controller reports the same firmware version as the target firmware, the download is skipped. This ultimately results in the firmware not being properly updated on the controller. This change removes the restriction that skips firmware download when the versions are equal. It covers scenarios where the USB connection can be disconnected at any time and ensures that firmware download can be retriggered after USB reconnection, allowing the Bluetooth firmware to be correctly and completely updated. Fixes: 3267c884cefa ("Bluetooth: btusb: Add support for QCA ROME chipset family") Cc: stable@vger.kernel.org Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: MediaTek MT7922: Add VID 0489 & PID e11dKamiyama Chiaki
Add VID 0489 & PID e11d for MediaTek MT7922 USB Bluetooth chip. Found in Dynabook GA/ZY (W6GAZY5RCL). The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e11d Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Kamiyama Chiaki <nercone@nercone.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for ASUS X870E / ProArt X870E-CreatorJavier Tia
Add USB device ID 13d3:3588 (IMC Networks/Azurewave) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the ASUS ROG STRIX X870E-E GAMING WIFI and ASUS ProArt X870E-Creator WiFi motherboards. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3588 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io> Tested-by: Ivan Lubnin <lubnin.ivan@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for TP-Link Archer TBE550EJavier Tia
Add USB device ID 0489:e116 (Foxconn/Hon Hai) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the TP-Link Archer TBE550E PCIe adapter. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e116 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb ... I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Thibaut FRANCOIS <tibo@humeurlibre.fr> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for MSI X870E Ace MaxJavier Tia
Add USB device ID 0489:e110 (Foxconn/Hon Hai) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the MSI X870E Ace Max motherboard. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e110 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb ... I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Nitin Gurram <nitin.reddy88@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for Gigabyte Z790 AORUS MASTER XJavier Tia
Add USB device ID 0489:e10f (Foxconn/Hon Hai) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the Gigabyte Z790 AORUS MASTER X motherboard. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e10f Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb ... I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Chapuis Dario <chapuisdario4@gmail.com> Tested-by: Evgeny Kapusta <3193631@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for Lenovo Legion Pro 7 16ARX9Javier Tia
Add USB device ID 0489:e0fa (Foxconn/Hon Hai) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the Lenovo Legion Pro 7 16ARX9 laptop. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0fa Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb ... I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Llewellyn Curran <melinko2003@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: Add MT7927 ID for ASUS ROG Crosshair X870E HeroJavier Tia
Add USB device ID 0489:e13a (Foxconn/Hon Hai) for the MediaTek MT7927 (Filogic 380) Bluetooth interface found on the ASUS ROG Crosshair X870E Hero WiFi motherboard. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=05 Cnt=04 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e13a Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb ... I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Link: https://bugzilla.kernel.org/show_bug.cgi?id=221096 Link: https://github.com/openwrt/mt76/issues/927 Signed-off-by: Javier Tia <floss@jetm.me> Tested-by: Jose Tiburcio Ribeiro Netto <jnetto@mineiro.io> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2026-04-13Bluetooth: btusb: refactor endpoint lookupJohan Hovold
Use the common USB helper for looking up bulk and interrupt endpoints instead of open coding. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2026-09-13 17:27:31 +0000