| Age | Commit message (Collapse) | Author |
|---|
|
Currently, we stop tx queues when we have one urb submitted. This means
we will immediately hit dev_hard_start_xmit's tx-queues-off ->
NETDEV_TX_BUSY case, and revert to the requeue -> gso_skb single-dequeue
path, and no longer be able to pack skbs without an xmit_more
indication.
Instead, allow a few urbs to be in-flight, with a limit of 16kB of data
outstanding (after which we will disable queues). With this, the tx path
will cause fewer requeues (and therefore non-packed transfers) under
normal loads.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-12-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that mctp-usblib supports DSP0283 v1.1 packet spanning, enable it in
our host-side transport driver.
Add a match for the new device subclass (0x02), and indicating spanning
mode to the usblib rx/tx implementation.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-11-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add some initial tests for the usblib receive path, where we're
extracting MCTP packets from incoming USB transfer data.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-10-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for packet spanning as defined in DSP0283 v1.1.
With the existing v1.0 implementation of multi-packet transfers, all we
need here is to adjust the buffer sizes to suit v1.1.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-9-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using the existing prepare/complete API, we can persist the rx skb
across receives to implement v1.1 packet spanning.
Alter the packet-extraction loop to allow truncated packets, returning
early with the skb persisted for the next IN urb completion. When we see
we have a complete packet, netif_rx() that. If the packet boundary
aligns with the urb completion, we can netif_rx() the whole thing.
Those intermediate packets are cloned from the original
(large-transfer-data) skb. Unlike existing behaviour, if the clone
fails, we drop just that clone, instead of the existing transfer skb.
This allows us to process the rest of the skb data, and any continuation
of the span into the next transfer.
One subtle change: the mctp_usblib_rx() helper now handles skbs with the
full transport header, so we shift the skb_pull() for the header data to
the helper, before doing the rx_bytes stats update.
We still need to handle non-spanning mode, so error out on
truncated-packet cases there.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-8-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the v1.1 update to DSP0283, we have a larger header field, of 13 bits
rather than 8.
In order to accommodate this, in preparation for proper v1.1 support,
expand our struct mctp_usb_hdr's len field to a u16, and endian-convert
when necessary. Because we don't yet support spanning mode, we will
never receive or transmit with the top 5 bits set, so we always mask
out anyway.
This allows for a future change where we allow spanning mode with
>512-byte transfers.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-7-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MCTP over USB spec allows us to pack multiple packets in one
transfer. Given the packet max length is 255, and the transfer max
length is 512, we can typically include two full-size packets per
urb submission.
To do this, we allow a struct mctp_usb_tx to persist a tx_ctx,
representing the ongoing context for a transmit. If possible, a TX skb
will be queued to the context and the send deferred until the context is
full, or the device queue reports no more packets.
This typically requires a linear buffer for the 512-byte TX, which we
allocate along with the TX context.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-6-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the RX processing in mctp-usblib, add TX processing alongside.
To accommodate packed transfers in DSP0283, where a transfer may contain
multiple MCTP packets, we move to a split process for the transmit API:
* push: create a new transmit context, and add a skb to it.
* send: callback to the driver implementation to send the (possibly
multi-packet) USB transfer
* complete: update skb accounting and release the tx context
The actual multi-packet transfer implementation will be added in the
next change; no tx context persists beyond the single send at present.
However, we use an anchor in the host driver implementation to track the
submitted TX urb when necessary.
While we're here, fix an inconsistency between tx and rx stats: both
should not include the transport header.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-5-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, we give-up on all non-zero status values on our IN/rx urb,
and do not re-queue the urb. This will stall the driver, and prevent
any further receive.
Instead, attempt a re-queue on transient errors, with a max of ten
successive failures. Handle EPIPE specially, by scheduling a
usb_clear_halt() in non-atomic context.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-4-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The processing of USB receive transfers is common to both sides of a
MCTP over USB transport. In order to support a future gadget driver,
move the current host-side driver into a new common file, mctp-usblib.
This currently handles the submit-complete-packetise process of the
receive path of the USB transport. We'll add transmit handling in an
upcoming change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-3-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The max packet size is smaller than the max transfer size, as we only
have a u8 length field in the transport header.
Add a define for the maximum representable length, and use that for our
check. Use this for the MTU maximum calculation too.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-2-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSP0283 v1.1.0 will introduce larger maximum packet sizes. In
preparation, indicate that the current maxima are specific to v1.0.x.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260724-dev-mctp-usb-1-1-v5-1-e66bbba0dbdc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
tested:
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: a0c2ccd9b5ad ("mctp: Add MCTP-over-serial transport binding")
Cc: stable@vger.kernel.org
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260715082021.46315-1-doruk@0sec.ai
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
mctp_i3c_mod_init() registers the I3C bus notifier and then walks the
existing buses with i3c_for_each_bus_locked(mctp_i3c_bus_add_new, NULL)
before registering the I3C device driver. If i3c_driver_register()
fails, the function returns the error directly, leaving the notifier
registered and every mctp_i3c_bus object created for the existing buses
allocated. The notifier is left pointing into the module that failed to
load and the bus list is leaked.
Mirror the module exit path on this failure: unregister the notifier and
tear down the buses that were added before returning the error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code.
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260715072517.13216-1-mhun512@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-7.1-rc8).
Conflicts:
drivers/net/ethernet/wangxun/txgbe/txgbe_aml.c
f67aead16e85 ("net: txgbe: rework service event handling")
57d39faed4c9 ("net: txgbe: improve functions of AML 40G devices")
net/rds/info.c
512db8267b73 ("rds: mark snapshot pages dirty in rds_info_getsockopt()")
6e94eeb2a2a6 ("rds: convert to getsockopt_iter")
Adjacent changes:
include/net/sock.h
1ee90b77b727 ("net: guard timestamp cmsgs to real error queue skbs")
f0de88303d5e ("net: make is_skb_wmem() available to modules")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the ndo_open path, a deferred queue open will report a failure, and
so the netdev will not be ndo_stop()ed, leaving us with the rx_retry
work potentially pending.
Don't report a deferred queue as an error, as we are still operational.
This means we use the ndo_stop() path for future cleanup, which handles
rx_retry_work cancellation.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260608-dev-mctp-usb-rx-requeue-v2-2-29a3aa507609@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It's possible that sequencing between setting ->stopped and cancelling
the rx_retry work (in ndo_stop) could leave us with an urb queued:
T1: ndo_stop T2: rx_retry_work
------------ ----------------
LD: ->stopped => false
ST: ->stopped <= true
usb_kill_urb()
mctp_usb_rx_queue()
usb_submit_urb()
cancel_delayed_work_sync()
That urb completion can then re-schedule rx_retry_work.
Strenghen the sequencing between the stop (preventing another requeue)
and the cancel by updating both atomically under a new rx lock. After
setting ->rx_stopped, and cancelling pending work, we know that the
requeue cannot occur, so all that's left is killing any pending urb.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260608-dev-mctp-usb-rx-requeue-v2-1-29a3aa507609@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
While touching this array, unify usage of whitespace in the list
terminator to what most other arrays are using.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260519153613.1594429-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, mctp_i2c_get_tx_flow_state() is called before the packet length
sanity check. This function marks a new flow as active in the MCTP core.
If the sanity check fails, mctp_i2c_xmit() returns early without calling
mctp_i2c_lock_nest(). This results in a mismatched locking state: the
flow is active, but the I2C bus lock was never acquired for it.
When the flow is later released, mctp_i2c_release_flow() will see the
active state and queue an unlock marker. The TX thread will then
decrement midev->i2c_lock_count from 0, causing it to underflow to -1.
This underflow permanently breaks the driver's locking logic, allowing
future transmissions to occur without holding the I2C bus lock, leading
to bus collisions and potential hardware hangs.
Move the mctp_i2c_get_tx_flow_state() call to after the length sanity
check to ensure we only transition the flow state if we are actually
going to proceed with the transmission and locking.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260423074741.201460-1-william@wkennington.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When 'midev->allow_rx' is false, the newly allocated skb isn't consumed
by netif_rx(), it needs to free the skb directly.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Link: https://patch.msgid.link/20260305143240.97592-1-haiyuewa@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
This driver takes a reference to the USB device during probe but does
not to release it on probe failures.
Drop the redundant device reference to fix the leak, reduce cargo
culting, make it easier to spot drivers where an extra reference is
needed, and reduce the risk of further memory leaks.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Cc: stable@vger.kernel.org # 6.15
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20260305104549.16110-1-johan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Set a 0xff value for i2c reads of an mctp-i2c device. Otherwise reads
will return "val" from the i2c bus driver. For i2c-aspeed and
i2c-npcm7xx that is a stack uninitialised u8.
Tested with "i2ctransfer -y 1 r10@0x34" where 0x34 is a mctp-i2c
instance, now it returns all 0xff.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20260113-mctp-read-fix-v1-1-70c4b59c741c@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MCTP I2C slave callback did not handle I2C_SLAVE_READ_REQUESTED
events. As a result, i2c read event will trigger repeated reception of
old data, reset rx_pos when a read request is received.
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Link: https://patch.msgid.link/20260108101829.1140448-1-zhangjian.3032@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"HDR support has finally been added. mipi-i3c-hci has been reworked and
Intel Nova Lake-S support has been added.
Subsystem:
- Add HDR transfer support
Drivers:
- dw: fix bus hang on Agilex5
- mipi-i3c-hci: Intel Nova Lake-S support, IOMMU support
- svc: HDR support"
* tag 'i3c/for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (28 commits)
regmap: i3c: switch to use i3c_xfer from i3c_priv_xfer
net: mctp i3c: switch to use i3c_xfer from i3c_priv_xfer
hwmon: (lm75): switch to use i3c_xfer from i3c_priv_xfer
i3c: document i3c_xfers
i3c: fix I3C_SDR bit number
i3c: master: svc: Add basic HDR mode support
i3c: master: svc: Replace bool rnw with union for HDR support
i3c: Switch to use new i3c_xfer from i3c_priv_xfer
i3c: Add HDR API support
i3c: master: add WQ_PERCPU to alloc_workqueue users
i3c: master: Remove i3c_device_free_ibi from i3c_device_remove
i3c: mipi-i3c-hci-pci: Set d3cold_delay to 0 for Intel controllers
i3c: mipi-i3c-hci-pci: Add LTR support for Intel controllers
i3c: mipi-i3c-hci-pci: Add exit callback
i3c: mipi-i3c-hci-pci: Change callback parameter
i3c: mipi-i3c-hci-pci: Allocate a structure for mipi_i3c_hci_pci device information
i3c: mipi-i3c-hci-pci: Factor out intel_reset()
i3c: mipi-i3c-hci-pci: Factor out private registers ioremapping
i3c: mipi-i3c-hci-pci: Constify driver data
i3c: mipi-i3c-hci-pci: Use readl_poll_timeout()
...
|
|
Switch to use i3c_xfer instead of i3c_priv_xfer because framework will
update to support HDR mode. i3c_priv_xfer is now an alias of i3c_xfer.
Replace i3c_device_do_priv_xfers() with i3c_device_do_xfers(..., I3C_SDR)
to align with the new API.
Prepare for removal of i3c_priv_xfer and i3c_device_do_priv_xfers().
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20251028-lm75-v1-2-9bf88989c49c@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The tx queue can become permanently stuck in a stopped state due to a
race condition between the URB submission path and its completion
callback.
The URB completion callback can run immediately after usb_submit_urb()
returns, before the submitting function calls netif_stop_queue(). If
this occurs, the queue state management becomes desynchronized, leading
to a stall where the queue is never woken.
Fix this by moving the netif_stop_queue() call to before submitting the
URB. This closes the race window by ensuring the network stack is aware
the queue is stopped before the URB completion can possibly run.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Signed-off-by: Jinliang Wang <jinliangw@google.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20251027065530.2045724-1-jinliangw@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We're not currently setting skb->mac_header on ingress, and the netdev
core rx path expects it. Without it, we'll hit a warning on DEBUG_NETDEV
from commit 1e4033b53db4 ("net: skb_reset_mac_len() must check if
mac_header was set")
Initialise the mac_header to refer to the USB transport header.
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20250829-mctp-usb-mac-header-v1-1-338ad725e183@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We stop queues in ndo_stop, so they need to be restarted in ndo_open.
This allows us to resume tx after a link down/up cycle.
Suggested-by: Nitin Singh <nitsingh@nvidia.com>
Fixes: 0791c0327a6e ("net: mctp: Add MCTP USB transport driver")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://patch.msgid.link/20250526-dev-mctp-usb-v1-1-c7bd6cb75aa0@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes to prepare for the 6.15 net-next PR.
No conflicts, adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
919f9f497dbc ("eth: bnxt: fix out-of-range access of vnic_info array")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, the condition for invalidating the tx flow in
mctp_i2c_invalidate_tx_flow() checked if `rc` was nonzero.
However, this could incorrectly trigger the invalidation
even when `rc > 0` was returned as a success status.
This patch updates the condition to explicitly check for `rc < 0`,
ensuring that only error cases trigger the invalidation.
Signed-off-by: Daniel Hsu <Daniel-Hsu@quantatw.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use skb_cow_head() prior to modifying the TX SKB. This is necessary
when the SKB has been cloned, to avoid modifying other shared clones.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Link: https://patch.msgid.link/20250306-matt-mctp-i2c-cow-v1-1-293827212681@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use skb_cow_head() prior to modifying the tx skb. This is necessary
when the skb has been cloned, to avoid modifying other shared clones.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Link: https://patch.msgid.link/20250306-matt-i3c-cow-head-v1-1-d5e6a5495227@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
net/ethtool/cabletest.c
2bcf4772e45a ("net: ethtool: try to protect all callback with netdev instance lock")
637399bf7e77 ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
No Adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
daddr can be NULL if there is no neighbour table entry present,
in that case the tx packet should be dropped.
saddr will usually be set by MCTP core, but check for NULL in case a
packet is transmitted by a different protocol.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Link: https://patch.msgid.link/20250304-mctp-i3c-null-v1-1-4416bbd56540@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add an implementation for DMTF DSP0283, which defines a MCTP-over-USB
transport. As per that spec, we're restricted to full speed mode,
requiring 512-byte transfers.
Each MCTP-over-USB interface is a peer-to-peer link to a single MCTP
endpoint, so no physical addressing is required (of course, that MCTP
endpoint may then bridge to further MCTP endpoints). Consequently,
interfaces will report with no lladdr data:
# mctp link
dev lo index 1 address 00:00:00:00:00:00 net 1 mtu 65536 up
dev mctpusb0 index 6 address none net 1 mtu 68 up
This is a simple initial implementation, with single rx & tx urbs, and
no multi-packet tx transfers - although we do accept multi-packet rx
from the device.
Includes suggested fixes from Santosh Puranik <spuranik@nvidia.com>.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Santosh Puranik <spuranik@nvidia.com>
Link: https://patch.msgid.link/20250221-dev-mctp-usb-v3-2-3353030fe9cc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.13-rc7).
Conflicts:
a42d71e322a8 ("net_sched: sch_cake: Add drop reasons")
737d4d91d35b ("sched: sch_cake: add bounds checks to host bulk flow fairness counts")
Adjacent changes:
drivers/net/ethernet/meta/fbnic/fbnic.h
3a856ab34726 ("eth: fbnic: add IRQ reuse support")
95978931d55f ("eth: fbnic: Revert "eth: fbnic: Add hardware monitoring support via HWMON interface"")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We found a timeout problem with the pldm command on our system. The
reason is that the MCTP-I3C driver has a race condition when receiving
multiple-packet messages in multi-thread, resulting in a wrong packet
order problem.
We identified this problem by adding a debug message to the
mctp_i3c_read function.
According to the MCTP spec, a multiple-packet message must be composed
in sequence, and if there is a wrong sequence, the whole message will be
discarded and wait for the next SOM.
For example, SOM → Pkt Seq #2 → Pkt Seq #1 → Pkt Seq #3 → EOM.
Therefore, we try to solve this problem by adding a mutex to the
mctp_i3c_read function. Before the modification, when a command
requesting a multiple-packet message response is sent consecutively, an
error usually occurs within 100 loops. After the mutex, it can go
through 40000 loops without any error, and it seems to run well.
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Signed-off-by: Leo Yang <Leo-Yang@quantatw.com>
Link: https://patch.msgid.link/20250107031529.3296094-1-Leo-Yang@quantatw.com
[pabeni@redhat.com: dropped already answered question from changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
No need to check the argument of i2c_unregister_device() because the
function itself does it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20241202082713.9719-1-wsa+renesas@sang-engineering.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
MCTP control protocol implementations are transport binding dependent.
Endpoint discovery is mandatory based on transport binding.
Message timing requirements are specified in each respective transport
binding specification.
However, we currently have no means to get this information from MCTP
links.
Add a IFLA_MCTP_PHYS_BINDING netlink link attribute, which represents
the transport type using the DMTF DSP0239-defined type numbers, returned
as part of RTM_GETLINK data.
We get an IFLA_MCTP_PHYS_BINDING attribute for each MCTP link, for
example:
- 0x00 (unspec) for loopback interface;
- 0x01 (SMBus/I2C) for mctpi2c%d interfaces; and
- 0x05 (serial) for mctpserial%d interfaces.
Signed-off-by: Khang Nguyen <khangng@os.amperecomputing.com>
Reviewed-by: Matt Johnston <matt@codeconstruct.com.au>
Link: https://patch.msgid.link/20241105071915.821871-1-khangng@os.amperecomputing.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
daddr can be NULL if there is no neighbour table entry present,
in that case the tx packet should be dropped.
saddr will usually be set by MCTP core, but check for NULL in case a
packet is transmitted by a different protocol.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Cc: stable@vger.kernel.org
Reported-by: Dung Cao <dung@os.amperecomputing.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241022-mctp-i2c-null-dest-v3-1-e929709956c5@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
0x7d and 0x7e bytes are meant to be escaped in the data portion of
frames, but this didn't occur since next_chunk_len() had an off-by-one
error. That also resulted in the final byte of a payload being written
as a separate tty write op.
The chunk prior to an escaped byte would be one byte short, and the
next call would never test the txpos+1 case, which is where the escaped
byte was located. That meant it never hit the escaping case in
mctp_serial_tx_work().
Example Input: 01 00 08 c8 7e 80 02
Previous incorrect chunks from next_chunk_len():
01 00 08
c8 7e 80
02
With this fix:
01 00 08 c8
7e
80 02
Cc: stable@vger.kernel.org
Fixes: a0c2ccd9b5ad ("mctp: Add MCTP-over-serial transport binding")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test various edge cases of inputs that contain characters
that need escaping.
This adds a new kunit suite for mctp-serial.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In tty, u8 is now used for data, ssize_t for sizes (with possible
negative error codes). Propagate these types (and use unsigned in
next_chunk_len()) to mctp.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20240808103549.429349-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we encounter an error on i2c packet transmit, we won't have a valid
flow anymore; since we didn't transmit a valid packet sequence, we'll
have to wait for the key to timeout instead of dropping it on the reply.
This causes the i2c lock to be held for longer than necessary.
Instead, invalidate the flow on TX error, and release the i2c lock
immediately.
Cc: Bonnie Lo <Bonnie_Lo@wiwynn.com>
Tested-by: Jerry C Chen <Jerry_C_Chen@wiwynn.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For mlxsw
Reviewed-by: Kory Maincent <Kory.maincent@bootlin.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> # for mctp-i2c
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240625083853.2205977-2-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
