| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"As usual bunch of new device and driver support and updates to
existing drivers and addition of Manivannan to help with reviews.
New Support:
- Mediatek MT8196 DSI PHY support
- Renesas RZ/G3L usb2 support
- Qualcomm SM8475 QMP USB PHY and PCIe phy, IPQ9650 QMP PCIe PHY,
QUSB2 Phy for Shikra SoC, Hawi support for QMP PCIe phy and UFS
PHY. Glymur QMP PCIe Multi-PHY driver and multiple link-mode
support, ipq5210 PCIe phy support
- Spacemit USB3/PCIe comb PHY driver
Updates:
- Samsung hdptx driver improvements for modernizing the register
access and code cleanup
- Qualcomm drop duplicate v8 DP headers, improved runtime handling
for qmp drivers
- Rockchip clock lane phase tuning and 2500 Mbps support and TMDS
rate handling
- Freescale imx8mq improvements for runtime pm, pd handling"
* tag 'phy-for-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (76 commits)
MAINTAINERS: Add Manivannan Sadhasivam as the Reviewer for Generic PHY Framework
phy: rockchip-samsung-dcphy: fix out-of-range max_register
phy: qcom: qmp-pcie: Add QMP PCIe Multi-PHY driver
dt-bindings: phy: qcom: Add Glymur QMP PCIe multiple link-mode PHY
phy: rockchip: samsung-hdptx: Consistently use bitfield macros
phy: rockchip: samsung-hdptx: Simplify GRF access with FIELD_PREP_WM16()
phy: rockchip: samsung-hdptx: Drop restrict_rate_change handling
phy: rockchip: samsung-hdptx: Consolidate consumer_put on error path
phy: rockchip: samsung-hdptx: Drop TMDS rate setup workaround
phy: rockchip: samsung-hdptx: Handle uncommitted PHY config changes
phy: rockchip: samsung-hdptx: Fix rate recalculation for 3.2GHz FRL
phy: rockchip: samsung-hdptx: Guard against clk rate integer underflow
phy: rockchip: samsung-hdptx: Prevent divide-by-zero when computing clk rate
phy: rockchip: samsung-hdptx: Fix rate recalculation for high bpc
phy: qcom: qmp-combo: Drop qmp_v4_calibrate_dp_phy
phy: qcom: qmp-combo: Correct pre-emphasis table for QMP v4 DP PHYs
phy: renesas: rcar-gen3-usb2: Ignore missing VBUS regulator
phy: qcom: qmp-pcie: Add support for SM8475 Gen3x1 PCIe0 port
phy: qcom: qmp-pcie: Add pcs_lane1 offset to V5 offsets
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Add SM8475 QMP PHY
...
|
|
Up until this patch, the only protocol change supported was between
1000Base-X/SGMII and 2500Base-X. The others require an RCW override
procedure which was lacking.
Since now the guts driver provides the means of applying this procedure,
make use of it and remove any comment which mentioned the limitation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20260721231603.67865-10-vladimir.oltean@nxp.com
Signed-off-by: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
|
|
fsl_samsung_hdmi_phy_probe() enables runtime PM, but the remove
callback does not disable it. Unbinding and rebinding the device
therefore results in the following warning on reprobe:
Unbalanced pm_runtime_enable!
Disable runtime PM after removing the clock provider.
Also undo the runtime PM operations when phy_clk_register() fails.
Otherwise, a failed probe leaves runtime PM enabled and the usage
counter incremented.
Signed-off-by: Fabio Estevam <festevam@nabladev.com>
Link: https://patch.msgid.link/20260729192830.487150-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On i.MX8MP, the USB PHY has a dedicated power domain that was previously
never powered off at runtime. With the introduction of runtime PM support,
the power domain will be powered off if the device is runtime suspended,
which breaks USB wakeup functionality.
To preserve wakeup functionality, mark the PHY power domain as runtime
always-on for i.MX8MP platform. To limit the behavior to i.MX8MP, add a
need_genpd_rpm_on to imx8mq_usb_phy_drvdata and set it as true for i.MX8MP.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-6-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Replace direct use of phy_ops pointer in of_device_id .data with a
dedicated imx8mq_usb_phy_drvdata structure. This allows per-variant
driver data to be extended in the future without changing the match
table.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-5-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The CR port is a simple 16-bit data/address parallel port that is
accessed through 32-bit MMIO registers for on-chip access to the
control registers inside the USB 3.0 femtoPHY. Add control register
regmap and export these registers by debugfs to help PHY's diagnostic.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-4-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add runtime PM support to ensure the PHY clocks are properly gated
when the PHY is not in use, reducing power consumption.
Clock management is moved from power_on()/power_off() callbacks into
the runtime_resume()/runtime_suspend() callbacks respectively. The PHY
subsystem core already holds a runtime PM reference around init() and
power_on/off() calls, so no explicit clock handling is needed there.
Use devm_clk_get_enabled() and devm_clk_get_optional_enabled() in
probe() to keep clocks enabled initially. This ensures the PHY remains
functional when CONFIG_PM is disabled, where runtime suspend/resume
callbacks are never invoked.
In tca_blk_typec_switch_set(), replace the manual clk_prepare_enable()
/ clk_disable_unprepare() pair with PM_RUNTIME_ACQUIRE_IF_ENABLED() to
guard register access against a concurrently suspended PHY.
Move devm_regulator_get() before pm_runtime_enable() to avoid having
to clean up runtime PM state on regulator acquisition failure.
In remove(), call pm_runtime_get_sync() before pm_runtime_disable() to
ensure the PHY is resumed and clocks are enabled before the devres
teardown disables them.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-3-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Set PHY wakeup capable because this PHY supports remote wakeup function.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-2-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If probe fails after imx95_usb_phy_get_tca() succeeds, the typec
switch leaks because the only cleanup path was in .remove(), which
never runs on probe failure.
Use devm_add_action_or_reset() so the switch is cleaned up on both
probe failure and driver removal. The imx95_usb_phy_put_tca() is no
longer needed, it will be removed in .remove() too.
Fixes: b58f0f86fd61 ("phy: fsl-imx8mq-usb: add tca function driver for imx95")
Cc: stable@vger.kernel.org
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260731-imx8mp-usb-phy-improvement-v8-1-2ec8d6b3854d@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The intention of the code is to extract the PCCR8_SGMIIa_CFG field out
of the "pccr" value, not to create a new value with the PCCR8_SGMIIa_CFG
field set to the "pccr" value.
Since FIELD_GET() is implemented as ((reg) & (mask)) >> __bf_shf(mask)
and FIELD_PREP() as (val) << __bf_shf(mask)) & (mask) and since "mask"
is GENMASK(2, 0), in practice there is no functional difference between
FIELD_GET() and FIELD_PREP(). But FIELD_GET() is logically the correct
helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260612125731.133330-1-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
probe error path
If mixel_lvds_phy_reset() fails in probe after pm_runtime_enable(),
the function returns directly without calling pm_runtime_disable(),
leaving runtime PM permanently enabled for the device.
Fix this by using devm_pm_runtime_enable() so that cleanup is
automatic on any probe failure or driver unbind. This also allows
removing the manual err label and the .remove callback.
Fixes: 06ff622d61d2 ("phy: freescale: Add i.MX8qm Mixel LVDS PHY support")
Acked-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260605-lvds-v2-1-3ce7539d1104@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The mixel_lvds_phy_reset() function pairs pm_runtime_resume_and_get()
with pm_runtime_put(). The asynchronous variant queues a work item
to handle the idle check and potential suspend, which can be cancelled
by a subsequent pm_runtime_disable() call if probe fails after the reset.
Switch to pm_runtime_put_sync() to run the idle check and suspend
synchronously.
Fixes: 06ff622d61d2 ("phy: freescale: Add i.MX8qm Mixel LVDS PHY support")
Reported-by: sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260605-lvds-v2-1-3ce7539d1104%40gmail.com
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260609-lvds-phy-v1-1-6ad790c6d0ea@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Introduce a driver for the networking lanes of the 10G Lynx SerDes
block, present on the majority of Layerscape and QorIQ (Freescale/NXP)
SoCs.
As with the 28G Lynx, the SerDes lanes come pre-initialized out of
reset and the consumers use them that way outside the Generic PHY
framework (for networking, the static configuration remains for the
entire SoC lifetime, whereas for SATA and PCIe, the hardware
reconfigures itself automatically for other link speeds).
The need for the Generic PHY framework comes specifically for networking
use cases where a static lane configuration is not sufficient. For
example a network MAC is connected to an SFP cage, where various SFP or
SFP+ modules can be connected. Each of them may require a different
SerDes protocol (SGMII, 1000Base-X, 10GBase-R), which phylink + sfp-bus
are responsible of figuring out. The phylink drivers are:
- enetc
- felix
- dpaa_eth (fman_memac)
- dpaa2-eth
- dpaa2-switch
and they all need to reconfigure the SerDes for the requested link mode,
using phy_set_mode_ext() (and phy_validate() to see if it is supported
in the first place).
Note that SerDes 2 on LS1088A is exclusively non-networking, so there is
currently no need for this driver. Therefore we skip matching on its
compatible string and do not probe on that device.
Co-developed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-16-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
lynx_28g_validate() suffers from the following shortcomings:
- Changing the protocol should not be possible if the source protocol of
the lane is unsupported. This is because lynx_28g_proto_conf[] only
covers the register deltas between any pair of supported lane modes,
but that delta is probably incomplete if the source protocol is, say,
PCIe (which is currently assimilated by the driver to
LANE_MODE_UNKNOWN).
lynx_28g_proto_conf() does refuse changing the protocol if the current
one is unsupported, but we shouldn't advertise it via phy_validate()
at all.
The phy_set_mode_ext() call should perform the exact same
verifications as phy_validate() did, in case the caller bypassed
phy_validate(). So we need to centralize the logic into a common
validation. But lynx_28g_set_mode() later needs the lane_mode that
this validation needs to compute anyway, so name the common helper
lynx_phy_mode_to_lane_mode() and let it return that lane_mode.
- Future core sanity checks on phy_validate() will want to differentiate
the case where this optional method is not implemented from the case
where the mode/submode is really not supported. So we shouldn't return
-EOPNOTSUPP from lynx_28g_validate(), but -EINVAL to signal that we do
implement the operation:
https://lore.kernel.org/linux-phy/aY2lFTIALH7qEJmM@shell.armlinux.org.uk/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-14-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It is unnecessary to rewrite a register if the masked field already
contains the desired value upon reading. The hardware behaviour does not
depend upon register writes with identical values.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-13-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some 10G Lynx SerDes blocks are big endian and require byte swapping
because the CPUs are little endian armv8 (LS1046A). Parse the
"big-endian" device tree property, and modify the base lynx_read() and
lynx_write() accessors to test this property before issuing either the
ioread32() or ioread32be() variants (as per
Documentation/driver-api/device-io.rst).
All other accessors - lynx_rmw(), lynx_lane_read(), lynx_lane_write(),
lynx_lane_rmw(), lynx_pll_read() - need to go through these endian-aware
helpers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-12-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Factor the device-agnostic logic from lynx_28g_probe() and
lynx_28g_remove() into lynx_probe() and lynx_remove() inside
phy-fsl-lynx-core.c. These will be shared with the 10G Lynx driver.
Since the PLL configuration, lane configuration and CDR lock detection
procedure are going to be different, introduce lynx_info function
pointers so that this code remains in the 28G Lynx driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-11-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In a future change, lynx_28g_pll_read_configuration() and
lynx_28g_lane_read_configuration() will be made methods of struct
lynx_info.
There is no functional reason, but lynx_28g_lane_read_configuration() is
called per lane and lynx_28g_pll_read_configuration() iterates over PLLs
internally. So the API exported by the lynx_info structure would not be
uniform. Change lynx_28g_pll_read_configuration() to also permit reading
the PLL configuration individually, and move the for loop at the call
site.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-10-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We need to be able to reference more function pointers in upcoming
patches. The struct lynx_info definitions are currently placed a bit up
in lynx-28g.c in order to be able to do that without function prototype
forward declarations, so move them downward to avoid that situation.
No functional change intended.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-9-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
For the 28G Lynx, there are situations where a protocol is not supported
on a lane despite there being a PCCR register and protocol converter
available:
- LX2160A SerDes 1: reference manual documents PCCD fields E25GC_CFG and
E25GD_CFG and protocol converter registers E25GCCR1..E25GCCR3 /
E25GDCR1..E25GDCR3, but nonetheless, Table 289. SerDes 1 protocol
mapping shows no RCW[SRDS_PRTCL_S1] value for which lanes C and D
support 25G
- when using the "fsl,lynx-28g" fallback compatible string, we don't
want to offer 25GbE because we don't know if the lane supports it,
even though we know how to reach the PCCR and protocol converter
registers for it.
But for the upcoming 10G Lynx SerDes, the above situations don't exist.
There, if we know how to reach the PCCR and protocol converter
registers on a lane, we implicitly know that the protocol is supported
there, so implementing priv->info->lane_supports_mode() would be
redundant.
Implement lynx_lane_supports_mode_default() which decides whether a lane
mode is supported just based on priv->info->get_pccr() and
priv->info->get_pcvt_offset().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-8-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The protocol converters on the 10G Lynx are architecturally similar, but
different in layout from the 28G Lynx ones.
Move lynx_pccr_read(), lynx_pccr_write(), lynx_pcvt_read() and
lynx_pcvt_write() from the 28G Lynx driver to the common module, and
permit each SerDes driver to provide just its own bits in order to use
this common API.
Currently, that just means that the direct calls to
lynx_28g_get_pcvt_offset() are modified to go through the
lynx->info->get_pcvt_offset() indirect function call, and similarly,
lynx_28g_get_pccr() through lynx->info->get_pccr().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-7-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The logic should be absolutely unchanged in the new 10G Lynx SerDes
driver, so let's move this to phy-fsl-lynx-core.c and update the 28G
Lynx driver to use the common variant.
While at it, update the call site, lynx_28g_lane_remap_pll(), to use the
new data structures, and refactor the NULL pll pointer check (the
current form triggers a checkpatch CHECK).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-6-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The goal is to avoid duplicating the core data structures when
introducing the new lynx-10g driver.
We move the following to phy-fsl-lynx-core:
- struct lynx_28g_pll -> struct lynx_pll. This has some
hardware-specific register fields which need to become hardware
agnostic (the PLL register layout is different for Lynx 10G), So:
- PLLnRSTCTL_DIS(pll->rstctl) becomes !pll->enabled
- PLLnRSTCTL_LOCK(pll->rstctl) becomes pll->locked
- FIELD_GET(PLLnCR1_FRATE_SEL, pll->cr1) becomes pll->frate_sel
- FIELD_GET(PLLnCR0_REFCLK_SEL, pll->cr0) becomes pll->refclk_sel
- struct lynx_28g_lane -> struct lynx_lane
- struct lynx_28g_priv -> struct lynx_priv
- field lane[LYNX_28G_NUM_LANE] has to be dynamically allocated. Not
all Lynx 10G SerDes blocks have 8 lanes.
- LYNX_28G_NUM_PLL -> LYNX_NUM_PLL. This is an architectural constant
which is the same for Lynx 10G as well.
To avoid major noise in the lynx-28g driver, we keep compatibility shims
(for now) where the old lynx_28g names are preserved, but translate to
the common data structures.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-5-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Do some preparation work for the introduction of the lynx-10g driver,
which will share a common backbone with the 28G Lynx SerDes.
This is just trivial stuff which can be moved without any surgery, and
is easy to follow but otherwise pollutes more serious changes.
The lane modes themselves are exported to a public header, because on
the 10G Lynx, the hardware requires implementing a procedure called
"RCW override". This requires coordination with drivers/soc/fsl/guts.c
to tell it that a SerDes lane needs to be switched to a different
protocol (enum lynx_lane_mode).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It is possible to bind the lynx-28g driver to an arbitrary device with
an OF node, using the driver_override mechanism that is available for
the platform bus, and trigger a crash this way:
$ echo 1ea0000.serdes > /sys/bus/platform/drivers/lynx-10g/unbind
$ echo lynx-28g > /sys/bus/platform/devices/1ea0000.serdes/driver_override
$ echo 1ea0000.serdes > /sys/bus/platform/drivers/lynx-28g/bind
Internal error: Oops: 0000000096000004 [#1] SMP
Hardware name: LS1028A RDB Board (DT)
pc : lynx_probe+0x118/0x4fc
lr : lynx_probe+0x110/0x4fc
Call trace:
lynx_probe+0x118/0x4fc (P)
lynx_28g_probe+0x54/0x7c
platform_probe+0x68/0xa4
really_probe+0x14c/0x2ec
__driver_probe_device+0xc8/0x170
device_driver_attach+0x58/0xa8
bind_store+0xd8/0x118
drv_attr_store+0x24/0x38
The crash is caused by the fact that of_device_get_match_data() returns
NULL (the bound device has a different compatible string) and this is
not checked.
There was a previous attempt to avoid this in commit c9d80e861034 ("phy:
lynx-28g: require an OF node to probe"), but the mechanism was not fully
understood and it only covered the case where the driver was bound to a
device with no OF node.
The issue was found during Sashiko review. Elevated privilege is
required to override the driver for a device, so the real life impact of
the issue should not be very high.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-3-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Sashiko points out that _of_phy_get() does not support a NULL returned
output from phy_provider->of_xlate(), just a valid pointer or a
pointer-encoded error.
When lynx_28g_probe() -> for_each_available_child_of_node() skips
over lanes which have OF nodes with status = "disabled", the
priv->lane[idx].phy pointer will remain NULL.
This NULL pointer may be propagated to lynx_28g_xlate() if the device
tree contains a phandle to the disabled lane AND fw_devlink did not
block probing for the consumer. In that case, the PHY core will crash
when trying to dereference the NULL phy pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260610151952.2141019-2-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for 25GBASE-R in the Lynx 28G SerDes PHY driver. This will
be used by the dpaa2-mac consumer on LX2160A with:
- phy_validate(phy, PHY_MODE_ETHERNET, PHY_INTERFACE_MODE_25GBASER) to
detect support.
- phy_set_mode_ext(phy, PHY_MODE_ETHERNET, PHY_INTERFACE_MODE_25GBASER)
to reconfigure the lane for this protocol.
The intended use case for dynamic protocol switching to 25GBase-R is
with SFP28 modules, and protocol switching is triggered by the SFP
module insertion. There also exists a 25GBase-KR use case, where the
protocol switching is covered by IEEE 802.3 clause 73 auto-negotiation.
However, that is not handled here; it merely needs the support added
here as basic ground work.
The lane frequency for 25GbE is sourced from a clock net frequency of
12.890625 GHz, as produced by PLLF or PLLS, further multiplied by the
lane by 2. The clock net frequencies produced by the PLLs are treated as
read-only by the driver, so the absence of a PLL provisioned for the
right clock net frequency implies absence of 25GbE support, even though
a lane might have the appropriate protocol converter for it.
In terms of implementation, the change consists of:
- determining at probe time if any PLL was preconfigured for the
required clock net frequency for 25GbE
- adding the default lane parameters for reconfiguring a lane to 25GbE
irrespective of the original protocol
- allowing this operating mode only on supported lanes, i.e. all lanes
of LX2162A SerDes #1, and LX2160A SerDes lanes 0-1, 4-7.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-6-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add driver support for probing on the new, per-instance and per-SoC
bindings, which provide the main benefit that they allow rejecting
unsupported protocols per lane (10GbE on SerDes 2 lanes 0-5), but they
also allow avoiding the creation of PHYs for lanes that don't exist
(LX2162A lanes 0-3).
For old device trees with just "fsl,lynx-28g", the only things that
change are:
- a probe time warning/encouragement to update the device tree. This is
warranted by the fact that using "fsl,lynx-28g" may already provide
incorrect behaviour (undetected absent 10GbE support on LX2160A
SerDes 2 lanes 0-5). But we retain bug compatibility nonetheless.
- the feature set is frozen in time (e.g. no 25GbE). Since we cannot
guarantee that this protocol will work on a lane, just err on the safe
side and don't offer it (and require a device tree update to get it).
In terms of code, the lynx_28g_supports_lane_mode() function prototype
changes. It was a SerDes-global function and now becomes per lane, to
reflect the specific capabilities each instance may have. The
implementation goes through priv->info->lane_supports_mode().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-5-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver will gain support for variants in an upcoming change, and
will use of_device_get_match_data() to deduce the running variant from
the compatible string.
Currently, the driver expects the schema at phy/fsl,lynx-28g.yaml, and
OF-based consumers, but doesn't enforce this. And it is possible for
user space to force-bind the driver to a device without OF node using
the driver_override sysfs.
To avoid future surprise crashes for an unsupported configuration,
explicitly test for the presence of an OF node and fail probing if
found.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Josua Mayer <josua@solid-run.com>
Link: https://patch.msgid.link/20260511150023.1903577-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This driver uses multiple regmaps, which will causes name conflicts
in debugfs like:
debugfs: '5f1a0000.phy' already exists in 'regmap'
Fix this by using a dedicated regmap config for each resource, each
having a dedicated regmap name.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260211144949.1128122-1-alexander.stein@ew.tq-group.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
On Layerscape, some Lynx SerDes consumers go through the PHY framework
(we call these 'managed' for the sake of this discussion; they are some
Ethernet lanes), and some consumers don't go through the PHY framework
(we call these 'unmanaged'; they are some unconverted Ethernet lanes,
plus all SATA and PCIe controllers).
A lane is initially unmanaged, and becomes managed when phy_init() is
called on it. Similarly, it becomes unmanaged again when phy_exit() is
called.
Managed lanes are supposed to have power management through
phy_power_on() and phy_power_off().
The lynx-28g SerDes driver, when it probes, probes on all lanes, but
needs to be careful to keep the unmanaged lanes powered on, because
those might be in use by consumers unaware that they need to call
phy_init() and phy_power_on(). This also applies after phy_exit() is
called - no guarantee is made about how the port may be used
afterwards - may be DPDK, may be something else which is unaware of
the PHY framework.
Given this state table:
State | Consumer calls phy_exit()? | Provider implements phy_exit()?
-------+----------------------------+--------------------------------
(a) | no | no
(b) | no | yes
(c) | yes | no
(d) | yes | yes
we are currently in state (a). This has the problem that when the
consumer fails to probe with -EPROBE_DEFER or is otherwise unbound,
the phy->init_count remains elevated and the lane never returns to the
unmanaged state (temporarily or not) as it should. Furthermore, the
second and subsequent phy_init() consumer calls are never passed on to
the provider driver.
We solve the above problem by implementing phy_exit() in the consumer,
and that moves us to state (c). But this creates the problem that a
balanced set of phy_init() and phy_exit() calls from the consumer will
effectively result in multiple lynx_28g_init() calls as seen by the
SerDes and nothing else - as the optional phy_ops :: exit() is not
implemented. But that actually doesn't work - the 28G Lynx SerDes can't
power down a lane which is already powered down; that call sequence
would time out and fail.
So actually we want to be in state (d), where both the provider and the
consumer implement phy_exit(). But we can only do that safely through
intermediary state (b), where the provider implements it first. This
effectively behaves just like (a), except it offers a safe migration
path for the consumer to call phy_exit() as mandated by the Generic PHY
API.
Extra development notes: ignoring the lynx_28g_power_on() error in
lynx_28g_exit() is a deliberate decision. The consumer can't deal with a
teardown path that is not error-free. Ignoring the error is not silent:
lynx_28g_power_on() -> lynx_28g_lane_reset() will print on failure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-4-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current procedure for power_off() and power_on() is the same as the
one used for major lane reconfiguration, aka halting. But this is
incorrect.
One would expect that a powered off lane causes the CDR (clock and data
recovery) loop of the link partner to lose lock onto its RX stream
(which suggests there are no longer any bit transitions => the channel
is inactive). However, it can be observed that this does not take place
(the CDR lock is still there), which means that a halted lane is not
powered off.
Implement the procedure mentioned in the block guide for powering down
a lane, and then back on. This means:
- lynx_28g_power_off() currently emits a HLT_REQ and waits for it to
clear. Rename it to lynx_28g_lane_halt() and keep using it for
lynx_28g_set_mode().
- lynx_28g_power_on() currently emits a RST_REQ and waits for it to
clear. This is the reset procedure - rename it to
lynx_28g_lane_reset(), and keep using it for lynx_28g_set_mode().
The "real" lynx_28g_power_off() should emit a STP_REQ and wait for it to
clear. And the "real" lynx_28g_power_on() should clear the DIS bit and
then perform a lane reset. Hook these methods to the phy_ops ::
power_off() and power_on() instead.
As opposed to lynx_28g_power_off() which is also directly hooked to the
PHY API, lynx_28g_lane_halt() isn't; just to lynx_28g_set_mode(), and
the call is being made in a state where we haven't yet made any change
to the lane. So it does make some limited amount of sense to code this
up such that if it fails, we make an attempt to reset the lane anyway
and let the consumer know that phy_set_mode_ext() failed.
Sort the field definitions in LNaTRSTCTL and LNaRRSTCTL in descending
order, and add new definitions for STP_REQ and DIS, previously unused.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260321011451.1557091-3-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There are various circumstances in which a lane halt, or a lane reset,
will fail to complete. If this happens, it will hang the kernel, which
only implements a busy loop with no timeout.
The circumstances in which this will happen are all bugs in nature:
- if we try to power off a powered off lane
- if we try to power off a lane that uses a PLL locked onto the wrong
refclk frequency (wrong RCW, but SoC boots anyway)
Actually, unbounded loops in the kernel are a bad practice, so let's use
read_poll_timeout() with a custom function that reads both LNaTRSTCTL
(lane transmit control register) and LNaRRSTCTL (lane receive control
register) and returns true when the request is done in both directions.
The HLT_REQ bit has to clear, whereas the RST_DONE bit has to get set.
Any time such an error happens, it is catastrophic and there is no point
in trying to propagate it to our callers:
- if lynx_28g_set_mode() -> lynx_28g_power_on() times out, we have
already reconfigured the lane, but returning an error would tell the
caller that we didn't
- if lynx_28g_power_off() times out, again not much for the consumer to
do to help get out of this situation - the phy_power_off() call is
probably made from a context that the consumer can't cancel, or it is
making it to return to a known state from a previous failure.
So just print an error if timeouts happen and let the driver control
flow continue. The entire point is just to not let the kernel freeze.
Suggested-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/lkml/d0c8bbf8-a0c5-469f-a148-de2235948c0f@solid-run.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260321011451.1557091-2-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The blamed commit introduced support for specifying individual lanes as
OF nodes in the device, and these can have status = "disabled".
When that happens, for_each_available_child_of_node() skips them and
lynx_28g_probe_lane() -> devm_phy_create() is not called, so lane->phy
will be NULL. Yet it will be dereferenced in lynx_28g_cdr_lock_check(),
resulting in a crash.
This used to be well handled in v3 of that patch:
https://lore.kernel.org/linux-phy/20250926180505.760089-14-vladimir.oltean@nxp.com/
but until v5 was merged, the logic to support per-lane OF nodes was
split into a separate change, and the per-SoC compatible strings patch
was deferred to a "part 2" set. The splitting was done improperly, and
that handling of NULL lane->phy pointers was not integrated into the
proper commit.
Fixes: 7df7d58abbd6 ("phy: lynx-28g: support individual lanes as OF PHY providers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260226182853.1103616-1-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"Core:
- Add suuport for "rx-polarity" and "tx-polarity" device tree
properties and phy common properties to manage this
New Support:
- Qualcomm Glymur PCIe Gen4 2-lanes PCIe phy, DP and edp phy, USB UNI
PHY and SMB2370 eUSB2 repeater. SC8280xp QMP UFS PHY, Kaanapali
PCIe phy and QMP PHY, QCS615 QMP USB3+DP PHY and driver support for
that.
- SpacemiT PCIe/combo PHY and K1 USB2 PHY driver.
- HDMI 2.1 FRL configuration support and driver enabling for rockchip
samsung-hdptx driver
- TI TCAN1046 phy
- Renesas RZ/V2H(P) and RZ/V2N usb3
- Mediatek MT8188 hdmi-phy
- Google Tensor SoC USB PHY driver
- Apple Type-C PHY
Updates:
- Subsystem conversion for clock round_rate() to determine_rate()
- TI USB3 DT schema conversion
- Samsung ExynosAutov920 usb3, combo hsphy and ssphy support"
* tag 'phy-for-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (143 commits)
phy: ti: phy-j721e-wiz: convert from divider_round_rate() to divider_determine_rate()
dt-bindings: phy: ti,control-phy-otghs: convert to DT schema
dt-bindings: phy: ti,phy-usb3: convert to DT schema
phy: tegra: xusb: Remove unused powered_on variable
phy: renesas: rcar-gen3-usb2: add regulator dependency
phy: GOOGLE_USB: add TYPEC dependency
phy: enter drivers/phy/Makefile even without CONFIG_GENERIC_PHY
phy: renesas: rcar-gen3-usb2: Use mux-state for phyrst management
phy: renesas: rcar-gen3-usb2: Add regulator for OTG VBUS control
phy: renesas: rcar-gen3-usb2: Use devm_pm_runtime_enable()
phy: renesas: rcar-gen3-usb2: Factor out VBUS control logic
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3E SoC
dt-bindings: phy: renesas,usb2-phy: Document mux-states property
dt-bindings: phy: renesas,usb2-phy: Document USB VBUS regulator
phy: rockchip: samsung-hdptx: Add HDMI 2.1 FRL support
phy: rockchip: samsung-hdptx: Extend rk_hdptx_phy_verify_hdmi_config() helper
phy: rockchip: samsung-hdptx: Switch to driver specific HDMI config
phy: rockchip: samsung-hdptx: Drop hw_rate driver data
phy: rockchip: samsung-hdptx: Compute clk rate from PLL config
phy: rockchip: samsung-hdptx: Cleanup *_cmn_init_seq lists
...
|
|
During the probe the refclk_pad pointer is set to NULL if the
'fsl,refclk-pad-mode' property is not defined in the devicetree node. But
in imx_hsio_configure_clk_pad() this pointer is unconditionally used which
could result in a NULL pointer dereference. So check the pointer before to
use it.
Fixes: 82c56b6dd24f ("phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support")
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://patch.msgid.link/20260114-phy-fsl-imx8qm-hsio-fix-null-pointer-dereference-v1-1-730e941be464@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is to resolve the problem of wakeup system by USB3 device insertion
if HSIOMIX on, in that case, the USB3 device detects RX term on so the
USB3 device doesn't downgrade to high-speed, we can't expect CONN wakeup
(for USB3) happen because the 24MHz OSC is required ON to trigger it.
Because the device works at Super-speed so DP/DM wakeup can't happen
either. Then the entire systen can't be waken up by such device attach
event.
With this override bit we can force the RX term off when enters system
suspend, and disable the override after system resume. Therefore, the
USB3 device will always downgrade to High-speed, then DP/DM wakeup can
always happen. It will correctly switch to Super-speed later when the
host reset it after the system resume back.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20260116101835.1810675-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add missing platform_set_drvdata() as the data will be used in remove().
Fixes: b58f0f86fd61 ("phy: fsl-imx8mq-usb: add tca function driver for imx95")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260120111646.3159766-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Disabling PHYs in runtime usually causes the client with external abort
exception or similar issue due to lack of API to notify clients about PHY
removal. This patch removes the possibility to unbind i.MX PHY drivers in
runtime.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260120111712.3159782-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
After U-Boot initializes PCIe with "pcie enum", Linux fails to detect
an NVMe disk on some boot cycles with:
phy phy-32f00000.pcie-phy.0: phy poweron failed --> -110
Discussion with NXP identified that the iMX8MP PCIe PHY PLL may fail to
lock when re-initialized without a reset cycle [1].
The issue reproduces on 7% of tested hardware platforms, with a 30-40%
failure rate per affected device across boot cycles.
Insert a reset cycle in the power-on routine to ensure the PHY is
initialized from a known state.
[1] https://community.nxp.com/t5/i-MX-Processors/iMX8MP-PCIe-initialization-in-U-Boot/m-p/2248437#M242401
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251223150254.1075221-1-rafael@beims.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
determine_rate()
The round_rate() clk ops is deprecated, so migrate this driver from
round_rate() to determine_rate() using the Coccinelle semantic patch
on the cover letter of this series.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://patch.msgid.link/20251212-phy-clk-round-rate-v3-1-beae3962f767@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
dev_set_drvdata() is called twice, it is sufficient to do it only once.
devm_of_phy_provider_register() can fail, and if it does, the
&priv->cdr_check work item is queued, but not cancelled, and the device
probing failed, so it will trigger use after free. This is a minor risk
though.
Resource initialization should be done a little earlier, in case we need
to dereference dev_get_drvdata() in lynx_28g_pll_read_configuration() or
in lynx_28g_lane_read_configuration().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-16-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We have "dev" which holds &pdev->dev, but we still dereference this
pointer 4 more times, instead of using the local variable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-15-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
While adding support for 25GbE, it was noticed that the RCCR0 and TTLCR0
registers have different values for this protocol than the 10GbE and
1GbE modes.
Expand the lynx_28g_proto_conf[] array with the expected values for the
currently supported protocols. These were dumped from a live system, and
are the out-of-reset values. It will ensure that the lane is configured
with these values when transitioning from 25GbE back into one of these
modes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-14-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver does not handle well protocol switching to or from USXGMII,
because it conflates it with 10GBase-R.
In the expected USXGMII use case, that isn't a problem, because SerDes
protocol switching performed by the lynx-28g driver is not necessary,
because USXGMII natively supports multiple speeds, as opposed to SFP
modules using 1000Base-X or 10GBase-R which require switching between
the 2.
That being said, let's be explicit, and in case someone requests a
protocol change which involves USXGMII, let's do the right thing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-13-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Lynx 28G is a multi-protocol SerDes - it handles serial Ethernet, PCIe,
SATA.
The driver should not use the phylib-specific phy_interface_t as an
internal data representation, but something specific to its internal
capabilities, and only convert to phy_interface_t when PHY_MODE_ETHERNET
is selected and used.
Otherwise it has no way of representing the non-Ethernet lanes (which
was not a short-term goal when the driver was introduced, and is not a
goal per se right now either, but should nonetheless be possible).
Prefer the "enum lynx_lane_mode" name over "lynx_28g_lane_mode", in
preparation of future Lynx 10G SerDes support. This SerDes is part of
the same IP family and has similar capabilities, and will reuse some
code, hence the common data type.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-12-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The current approach of transitioning from one SerDes protocol to
another in lynx_28g_set_lane_mode() is too poetic.
Because the driver only supports 1GbE and 10GbE, it only modifies those
registers which it knows are different between these two modes. However,
that is hardly extensible for 25GbE, 40GbE, backplane modes, etc.
We need something more systematic to make sure that all lane and
protocol converter registers are written to consistent values, no matter
what was the source lane mode.
For that, we need to introduce tables with register field values, for
each supported lane mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-11-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Eliminate the need to calculate a lane_offset manually, and generate
some macros which access the protocol converter corresponding to the
correct lane in the PCC* registers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-10-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver will need to become more careful with the values it writes to
the TX and RX equalization registers. As a preliminary step, convert the
magic numbers to macros defining the register field meanings.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-9-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Reduce the number of bit field definitions required in this driver (in
the worst case, a read form and a write form), by defining just the
mask, and using the FIELD_GET() and FIELD_PREP() API from
<linux/bitfield.h> with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251125114847.804961-8-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
