| Age | Commit message (Collapse) | Author |
|---|
|
Only enter the sense_key switch when the command returned CHECK
CONDITION with valid, non-deferred sense. The old condition let deferred
or invalid sense fall through and mis-handle the I/O.
Fixes: 03aba2f79594 ("[SCSI] sd/scsi_lib simplify sd_rw_intr and scsi_io_completion")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260707030333.22245-4-yangxiuwei@kylinos.cn
Signed-off-by: Martin K. Petersen (Oracle) <mkp@kernel.org>
|
|
sd_set_special_bvec() allocates a special payload page for UNMAP and
WRITE SAME commands. If scsi_alloc_sgtables() fails afterward in
sd_setup_unmap_cmnd() or sd_setup_write_same{10,16}_cmnd(), the SCSI
midlayer does not call uninit_command() because RQF_DONTPREP is not set
yet, leaking the page.
Call sd_uninit_command() on error, and clear RQF_SPECIAL_PAYLOAD after
freeing the page.
Fixes: 81d926e8b552 ("sd: split sd_setup_discard_cmnd")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://patch.msgid.link/20260707030333.22245-3-yangxiuwei@kylinos.cn
Signed-off-by: Martin K. Petersen (Oracle) <mkp@kernel.org>
|
|
After device_add(&sdkp->disk_dev) succeeds, sd_large_pool_create()
failure must unregister disk_dev and let scsi_disk_release() free
sdkp. Going through out_free_index kfree()s an already registered device
and leaks the sysfs entry.
Fixes: 7179e626b76e ("scsi: sd: Enable sector size > PAGE_SIZE in SCSI sd driver")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://patch.msgid.link/20260707030333.22245-2-yangxiuwei@kylinos.cn
Signed-off-by: Martin K. Petersen (Oracle) <mkp@kernel.org>
|
|
As found by smatch-ci, scsi_execute_cmd() can return negative or positve
values so we should use a int instead of unsigned int.
Fixes: b4d0c33a32c3 ("scsi: sd: Fix sshdr use in sd_spinup_disk")
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/linux-scsi/agFbI7E6JQwd3wGW@stanley.mountain/T/#u
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260511175317.114007-1-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If device_add(&sdkp->disk_dev) fails, put_device() runs
scsi_disk_release(), which frees the scsi_disk but leaves the gendisk
referenced. The device_add_disk() error path in sd_probe() calls
put_disk(gd); call put_disk(gd) here to mirror that cleanup.
Fixes: 265dfe8ebbab ("scsi: sd: Free scsi_disk device via put_device()")
Cc: stable@vger.kernel.org
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Link: https://patch.msgid.link/20260330014952.152776-1-yangxiuwei@kylinos.cn
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The WRITE SAME(16) and WRITE SAME(10) SCSI commands use a page from a
dedicated mempool (sd_page_pool) for their payload. This pool was
initialized to allocate single pages, which was sufficient as long as the
device sector size did not exceed the PAGE_SIZE.
Given that block layer now supports block size upto 64KB, i.e. beyond
PAGE_SIZE, initialize a large page pool in sd_probe() if a higher sector
device is attached, ensuring atomicity. Adapt sd_set_special_bvec() to use
large page pool when a higher sector size device is attached. Hence enable
sector sizes > PAGE_SIZE in SCSI sd driver.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Swarna Prabhu <s.prabhu@samsung.com>
Co-developed-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Link: https://patch.msgid.link/20260219043741.276729-2-sw.prabhu6@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Make it easier to find these error messages with grep. This patch has been
created as follows:
* Delete all occurrences of the following regular expression:
"[[:blank:]]*\\*\n[[:blank:]]*"
* Split long lines manually where necessary.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260114175054.4118163-6-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the sd_fops definition such that the sd_unlock_native_capacity()
forward declaration can be removed.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260114175054.4118163-5-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the scsi_disk_release() function definition such that its forward
declaration can be removed.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260114175054.4118163-4-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the sd_config_discard() function definition such that its
forward declaration can be removed.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260114175054.4118163-3-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the sd_remove() function definition such that the sd_shutdown()
forward declaration can be removed.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260114175054.4118163-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The SCSI subsystem has implemented dedicated callbacks for probe, remove
and shutdown. Make use of them. This fixes a runtime warning about the
driver needing to be converted to the bus probe method.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/8ad5a00c2ad2a64b81350ae3fab02fbe430f306d.1766133330.git.u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This aligns with what other subsystems do, reduces boilerplate a bit for
device drivers and is less error prone.
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/ac17fdea58e384cb514c639306d48ce0005820b0.1766133330.git.u.kleine-koenig@baylibre.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block updates from Jens Axboe:
"Followup set of fixes and updates for block for the 6.19 merge window.
NVMe had some late minute debates which lead to dropping some patches
from that tree, which is why the initial PR didn't have NVMe included.
It's here now. This pull request contains:
- NVMe pull request via Keith:
- Subsystem usage cleanups (Max)
- Endpoint device fixes (Shin'ichiro)
- Debug statements (Gerd)
- FC fabrics cleanups and fixes (Daniel)
- Consistent alloc API usages (Israel)
- Code comment updates (Chu)
- Authentication retry fix (Justin)
- Fix a memory leak in the discard ioctl code, if the task is being
interrupted by a signal at just the wrong time
- Zoned write plugging fixes
- Add ioctls for for persistent reservations
- Enable per-cpu bio caching by default
- Various little fixes and tweaks"
* tag 'block-6.19-20251208' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux: (27 commits)
nvme-fabrics: add ENOKEY to no retry criteria for authentication failures
nvme-auth: use kvfree() for memory allocated with kvcalloc()
nvmet-tcp: use kvcalloc for commands array
nvmet-rdma: use kvcalloc for commands and responses arrays
nvme: fix typo error in nvme target
nvmet-fc: use pr_* print macros instead of dev_*
nvmet-fcloop: remove unused lsdir member.
nvmet-fcloop: check all request and response have been processed
nvme-fc: check all request and response have been processed
block: fix memory leak in __blkdev_issue_zero_pages
block: fix comment for op_is_zone_mgmt() to include RESET_ALL
block: Clear BLK_ZONE_WPLUG_PLUGGED when aborting plugged BIOs
blk-mq: Abort suspend when wakeup events are pending
blk-mq: add blk_rq_nr_bvec() helper
block: add IOC_PR_READ_RESERVATION ioctl
block: add IOC_PR_READ_KEYS ioctl
nvme: reject invalid pr_read_keys() num_keys values
scsi: sd: reject invalid pr_read_keys() num_keys values
block: enable per-cpu bio cache by default
block: use bio_alloc_bioset for passthru IO by default
...
|
|
The pr_read_keys() interface has a u32 num_keys parameter. The SCSI
PERSISTENT RESERVE IN command has a maximum READ KEYS service action
size of 65536 bytes. Reject num_keys values that are too large to fit
into the SCSI command.
This will become important when pr_read_keys() is exposed to untrusted
userspace via an <linux/pr.h> ioctl.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In addition to the already existing manage_shutdown,
manage_system_start_stop and manage_runtime_start_stop device scsi_disk
attributes, add manage_restart, which allows the high-level device
driver (sd) to manage the device power state for SYSTEM_RESTART if set
to 1.
This attribute is necessary for the following commit "ata: stop disk on
restart if ACPI power resources are found" to avoid a potential disk
power failure in the case the SATA power connector does not retain the
power state after a restart.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Markus Probst <markus.probst@posteo.de>
Link: https://patch.msgid.link/20251104142413.322347-2-markus.probst@posteo.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"Usual driver updates (ufs, mpi3mr, lpfc, pm80xx, mpt3sas) plus
assorted cleanups and fixes.
The only core update is to sd.c and is mostly cosmetic"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (105 commits)
scsi: MAINTAINERS: Update FC element owners
scsi: mpt3sas: Update driver version to 54.100.00.00
scsi: mpt3sas: Add support for 22.5 Gbps SAS link rate
scsi: mpt3sas: Suppress unnecessary IOCLogInfo on CONFIG_INVALID_PAGE
scsi: mpt3sas: Fix crash in transport port remove by using ioc_info()
scsi: ufs: ufs-qcom: Add support for limiting HS gear and rate
scsi: ufs: pltfrm: Add DT support to limit HS gear and gear rate
scsi: ufs: ufs-qcom: Remove redundant re-assignment to hs_rate
scsi: ufs: dt-bindings: Document gear and rate limit properties
scsi: ufs: core: Fix data race in CPU latency PM QoS request handling
scsi: libfc: Fix potential buffer overflow in fc_ct_ms_fill()
scsi: storvsc: Remove redundant ternary operators
scsi: ufs: core: Change MCQ interrupt enable flow
scsi: smartpqi: Replace kmalloc() + copy_from_user() with memdup_user()
scsi: hpsa: Replace kmalloc() + copy_from_user() with memdup_user()
scsi: hpsa: Fix potential memory leak in hpsa_big_passthru_ioctl()
scsi: lpfc: Copyright updates for 14.4.0.11 patches
scsi: lpfc: Update lpfc version to 14.4.0.11
scsi: lpfc: Convert debugfs directory counts from atomic to unsigned int
scsi: lpfc: Clean up extraneous phba dentries
...
|
|
The sd_revalidate_disk() function currently returns 0 for both success
and memory allocation failure. Since none of its callers use the return
value, this return code is both unnecessary and potentially misleading.
Change the return type of sd_revalidate_disk() from int to void
and remove all return value handling. This makes the function
semantics clearer and avoids confusion about unused return codes.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Link: https://lore.kernel.org/r/20250825183940.13211-4-abinashsinghlalotra@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The SCSI disk driver prints a warning when kmalloc() fails in
sd_revalidate_disk(). This is redundant because the page allocator
already reports failures unless __GFP_NOWARN is used. Keeping the extra
message only adds noise to the kernel log.
Remove the unnecessary sd_printk() call. Control flow is unchanged.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Link: https://lore.kernel.org/r/20250825183940.13211-3-abinashsinghlalotra@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A build warning was triggered due to excessive stack usage in
sd_revalidate_disk():
drivers/scsi/sd.c: In function ‘sd_revalidate_disk.isra’:
drivers/scsi/sd.c:3824:1: warning: the frame size of 1160 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This is caused by a large local struct queue_limits (~400B) allocated on
the stack. Replacing it with a heap allocation using kmalloc()
significantly reduces frame usage. Kernel stack is limited (~8 KB), and
allocating large structs on the stack is discouraged. As the function
already performs heap allocations (e.g. for buffer), this change fits
well.
Fixes: 804e498e0496 ("sd: convert to the atomic queue limits API")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Abinash Singh <abinashsinghlalotra@gmail.com>
Link: https://lore.kernel.org/r/20250825183940.13211-2-abinashsinghlalotra@gmail.com
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instances are happier that way and it makes more sense anyway -
the only part of the result that is related to partition we are given
is the start sector, and that has been filled in by the caller.
Everything else is a function of the disk. Only one instance
(DASD) is ever looking at anything other than bdev->bd_disk and
that one is trivial to adjust.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Instances are passed struct block_device *bdev argument; the only thing
it is used for (if it's used in the first place) is bdev->bd_disk.
Might as well pass that in the first place...
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull more SCSI updates from James Bottomley:
"This is mostly fixes and cleanups and code reworks that trickled in
across the merge window and the weeks leading up. The only substantive
update is the Mediatek ufs driver which accounts for the bulk of the
additions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (37 commits)
scsi: libsas: Use a bool for sas_deform_port() second argument
scsi: libsas: Move declarations of internal functions to sas_internal.h
scsi: libsas: Make sas_get_ata_info() static
scsi: libsas: Simplify sas_ata_wait_eh()
scsi: libsas: Refactor dev_is_sata()
scsi: sd: Make sd shutdown issue START STOP UNIT appropriately
scsi: arm64: dts: mediatek: mt8195: Add UFSHCI node
scsi: dt-bindings: mediatek,ufs: add MT8195 compatible and update clock nodes
scsi: dt-bindings: mediatek,ufs: Add ufs-disable-mcq flag for UFS host
scsi: ufs: ufs-mediatek: Add UFS host support for MT8195 SoC
scsi: ufs: ufs-pci: Remove control of UIC Completion interrupt for Intel MTL
scsi: ufs: core: Do not write interrupt enable register unnecessarily
scsi: ufs: core: Set and clear UIC Completion interrupt as needed
scsi: ufs: core: Remove duplicated code in ufshcd_send_bsg_uic_cmd()
scsi: ufs: core: Move ufshcd_enable_intr() and ufshcd_disable_intr()
scsi: ufs: ufs-pci: Remove UFS PCI driver's ->late_init() call back
scsi: ufs: ufs-pci: Fix default runtime and system PM levels
scsi: ufs: ufs-pci: Fix hibernate state transition for Intel MTL-like host controllers
scsi: ufs: host: mediatek: Support FDE (AES) clock scaling
scsi: ufs: host: mediatek: Support clock scaling with Vcore binding
...
|
|
Pull SCSI updates from James Bottomley:
"Smaller set of driver updates than usual (ufs, lpfc, mpi3mr).
The rest (including the core file changes) are doc updates and some
minor bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
scsi: libiscsi: Initialize iscsi_conn->dd_data only if memory is allocated
scsi: scsi_transport_fc: Add comments to describe added 'rport' parameter
scsi: bfa: Double-free fix
scsi: isci: Fix dma_unmap_sg() nents value
scsi: mvsas: Fix dma_unmap_sg() nents value
scsi: elx: efct: Fix dma_unmap_sg() nents value
scsi: scsi_transport_fc: Change to use per-rport devloss_work_q
scsi: ufs: exynos: Fix programming of HCI_UTRL_NEXUS_TYPE
scsi: core: Fix kernel doc for scsi_track_queue_full()
scsi: ibmvscsi_tgt: Fix dma_unmap_sg() nents value
scsi: ibmvscsi_tgt: Fix typo in comment
scsi: mpi3mr: Update driver version to 8.14.0.5.50
scsi: mpi3mr: Serialize admin queue BAR writes on 32-bit systems
scsi: mpi3mr: Drop unnecessary volatile from __iomem pointers
scsi: mpi3mr: Fix race between config read submit and interrupt completion
scsi: ufs: ufs-qcom: Enable QUnipro Internal Clock Gating
scsi: ufs: core: Add ufshcd_dme_rmw() to modify DME attributes
scsi: ufs: ufs-qcom: Update esi_vec_mask for HW major version >= 6
scsi: core: Use scsi_cmd_priv() instead of open-coding it
scsi: qla2xxx: Remove firmware URL
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull fallocate updates from Christian Brauner:
"fallocate() currently supports creating preallocated files
efficiently. However, on most filesystems fallocate() will preallocate
blocks in an unwriten state even if FALLOC_FL_ZERO_RANGE is specified.
The extent state must later be converted to a written state when the
user writes data into this range, which can trigger numerous metadata
changes and journal I/O. This may leads to significant write
amplification and performance degradation in synchronous write mode.
At the moment, the only method to avoid this is to create an empty
file and write zero data into it (for example, using 'dd' with a large
block size). However, this method is slow and consumes a considerable
amount of disk bandwidth.
Now that more and more flash-based storage devices are available it is
possible to efficiently write zeros to SSDs using the unmap write
zeroes command if the devices do not write physical zeroes to the
media.
For example, if SCSI SSDs support the UMMAP bit or NVMe SSDs support
the DEAC bit[1], the write zeroes command does not write actual data
to the device, instead, NVMe converts the zeroed range to a
deallocated state, which works fast and consumes almost no disk write
bandwidth.
This series implements the BLK_FEAT_WRITE_ZEROES_UNMAP feature and
BLK_FLAG_WRITE_ZEROES_UNMAP_DISABLED flag for SCSI, NVMe and
device-mapper drivers, and add the FALLOC_FL_WRITE_ZEROES and
STATX_ATTR_WRITE_ZEROES_UNMAP support for ext4 and raw bdev devices.
fallocate() is subsequently extended with the FALLOC_FL_WRITE_ZEROES
flag. FALLOC_FL_WRITE_ZEROES zeroes a specified file range in such a
way that subsequent writes to that range do not require further
changes to the file mapping metadata. This flag is beneficial for
subsequent pure overwriting within this range, as it can save on block
allocation and, consequently, significant metadata changes"
* tag 'vfs-6.17-rc1.fallocate' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
ext4: add FALLOC_FL_WRITE_ZEROES support
block: add FALLOC_FL_WRITE_ZEROES support
block: factor out common part in blkdev_fallocate()
fs: introduce FALLOC_FL_WRITE_ZEROES to fallocate
dm: clear unmap write zeroes limits when disabling write zeroes
scsi: sd: set max_hw_wzeroes_unmap_sectors if device supports SD_ZERO_*_UNMAP
nvmet: set WZDS and DRB if device enables unmap write zeroes operation
nvme: set max_hw_wzeroes_unmap_sectors if device supports DEAC bit
block: introduce max_{hw|user}_wzeroes_unmap_sectors to queue limits
|
|
Commit aa3998dbeb3a ("ata: libata-scsi: Disable scsi device
manage_system_start_stop") enabled libata EH to manage device power mode
trasitions for system suspend/resume and removed the flag from
ata_scsi_dev_config. However, since the sd_shutdown() function still
relies on the manage_system_start_stop flag, a spin-down command is not
issued to the disk with command "echo 1 > /sys/block/sdb/device/delete"
sd_shutdown() can be called for both system/runtime start stop
operations, so utilize the manage_run_time_start_stop flag set in the
ata_scsi_dev_config and issue a spin-down command during disk removal
when the system is running. This is in addition to when the system is
powering off and manage_shutdown flag is set. The
manage_system_start_stop flag will still be used for drivers that still
set the flag.
Fixes: aa3998dbeb3a ("ata: libata-scsi: Disable scsi device manage_system_start_stop")
Signed-off-by: Salomon Dushimirimana <salomondush@google.com>
Link: https://lore.kernel.org/r/20250724214520.112927-1-salomondush@google.com
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
sd_read_block_limits_ext() currently assumes that vpd->len excludes the
size of the page header. However, vpd->len describes the size of the entire
VPD page, therefore the sanity check is incorrect.
In practice this is not really a problem since we don't attach VPD
pages unless they actually report data trailing the header. But fix
the length check regardless.
This issue was identified by Wukong-Agent (formerly Tencent Woodpecker), a
code security AI agent, through static code analysis.
[mkp: rewrote patch description]
Signed-off-by: jackysliu <1972843537@qq.com>
Link: https://lore.kernel.org/r/tencent_ADA5210D1317EEB6CD7F3DE9FE9DA4591D05@qq.com
Fixes: 96b171d6dba6 ("scsi: core: Query the Block Limits Extension VPD page")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the device supports the Write Zeroes command and the zeroing mode
is set to SD_ZERO_WS16_UNMAP or SD_ZERO_WS10_UNMAP, this means that the
device supports unmap Write Zeroes, so set the corresponding
max_hw_write_zeroes_unmap_sectors to max_write_zeroes_sectors on the
device's queue limit.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://lore.kernel.org/20250619111806.3546162-5-yi.zhang@huaweicloud.com
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
scsi_add_lun() tests the device vendor string of SCSI devices to detect
if a SCSI device is in fact an ATA device, in order to correctly handle
SATL power management. The function scsi_cdl_enable() also requires
knowing if a SCSI device is an ATA device to control the state of the
device CDL feature but this function does that by testing for the
presence of the VPD page 89h (ATA INFORMATION page).
sd_read_write_same() also has a similar test.
Simplify these different methods by adding the is_ata field to struct
scsi_device to remember that a SCSI device is in fact an ATA one based
on the device vendor name test. This field can also allow low level
SCSI host adapter drivers to take special actions for ATA devices
(e.g. to better handle ATA NCQ errors).
With this, simplify scsi_cdl_enable() and sd_read_write_same().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250611093421.2901633-1-dlemoal@kernel.org
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Having a variable length array at the end of scsi_stream_status_header
only causes problems. Remove it and switch sd_is_perm_stream(), which is
the only place that currently uses it, to use the scsi_stream_status
directly following it in the local buf structure.
Besides being a much better data structure design, this also avoids a
-Wflex-array-member-not-at-end warning.
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250505060640.3398500-1-hch@lst.de
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull io_uring updates from Jens Axboe:
"Not a lot in terms of features this time around, mostly just cleanups
and code consolidation:
- Support for PI meta data read/write via io_uring, with NVMe and
SCSI covered
- Cleanup the per-op structure caching, making it consistent across
various command types
- Consolidate the various user mapped features into a concept called
regions, making the various users of that consistent
- Various cleanups and fixes"
* tag 'for-6.14/io_uring-20250119' of git://git.kernel.dk/linux: (56 commits)
io_uring/fdinfo: fix io_uring_show_fdinfo() misuse of ->d_iname
io_uring: reuse io_should_terminate_tw() for cmds
io_uring: Factor out a function to parse restrictions
io_uring/rsrc: require cloned buffers to share accounting contexts
io_uring: simplify the SQPOLL thread check when cancelling requests
io_uring: expose read/write attribute capability
io_uring/rw: don't gate retry on completion context
io_uring/rw: handle -EAGAIN retry at IO completion time
io_uring/rw: use io_rw_recycle() from cleanup path
io_uring/rsrc: simplify the bvec iter count calculation
io_uring: ensure io_queue_deferred() is out-of-line
io_uring/rw: always clear ->bytes_done on io_async_rw setup
io_uring/rw: use NULL for rw->free_iovec assigment
io_uring/rw: don't mask in f_iocb_flags
io_uring/msg_ring: Drop custom destructor
io_uring: Move old async data allocation helper to header
io_uring/rw: Allocate async data through helper
io_uring/net: Allocate msghdr async data through helper
io_uring/uring_cmd: Allocate async data through generic helper
io_uring/poll: Allocate apoll with generic alloc_cache helper
...
|
|
Currently only stacked devices need to explicitly enable atomic writes by
setting BLK_FEAT_ATOMIC_WRITES_STACKED flag.
This does not work well for device mapper stacking devices, as there many
sets of limits are stacked and what is the 'bottom' and 'top' device can
swapped. This means that BLK_FEAT_ATOMIC_WRITES_STACKED needs to be set
for many queue limits, which is messy.
Generalize enabling atomic writes enabling by ensuring that all devices
must explicitly set a flag - that includes NVMe, SCSI sd, and md raid.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20250116170301.474130-2-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a helper that freezes the queue, updates the queue limits and
unfreezes the queue and convert all open coded versions of that to the
new helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250110054726.1499538-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add support for sending user-meta buffer. Set tags to be checked
using flags specified by user/block-layer.
With this change, BIP_CTRL_NOCHECK becomes unused. Remove it.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241128112240.8867-10-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The write_hint is only used for read/write requests, which must have a
bio attached to them. Just use the bio field instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241112170050.1612998-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr).
There are no user visible core changes and a whole series of minor
updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (86 commits)
scsi: smartpqi: update driver version to 2.1.30-031
scsi: smartpqi: fix volume size updates
scsi: smartpqi: fix rare system hang during LUN reset
scsi: smartpqi: add new controller PCI IDs
scsi: smartpqi: add counter for parity write stream requests
scsi: smartpqi: correct stream detection
scsi: smartpqi: Add fw log to kdump
scsi: bnx2fc: Remove some unused fields in struct bnx2fc_rport
scsi: qla2xxx: Remove the unused 'del_list_entry' field in struct fc_port
scsi: ufs: core: Remove ufshcd_urgent_bkops()
scsi: core: Remove obsoleted declaration for scsi_driverbyte_string()
scsi: bnx2i: Remove unused declarations
scsi: core: Simplify an alloc_workqueue() invocation
scsi: ufs: Simplify alloc*_workqueue() invocation
scsi: stex: Simplify an alloc_ordered_workqueue() invocation
scsi: scsi_transport_fc: Simplify alloc_workqueue() invocations
scsi: snic: Simplify alloc_workqueue() invocations
scsi: qedi: Simplify an alloc_workqueue() invocation
scsi: qedf: Simplify alloc_workqueue() invocations
scsi: myrs: Simplify an alloc_ordered_workqueue() invocation
...
|
|
Ff the device returns page 0xb1 with length 8 (happens with qemu v2.x, for
example), sd_read_block_characteristics() may attempt an out-of-bounds
memory access when accessing the zoned field at offset 8.
Fixes: 7fb019c46eee ("scsi: sd: Switch to using scsi_device VPD pages")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Wilck <mwilck@suse.com>
Link: https://lore.kernel.org/r/20240912134308.282824-1-mwilck@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During system resume, sd_start_stop_device() submits a START STOP UNIT
command to the SCSI device that is being resumed. That command is not
retried in case of a unit attention and hence may fail. An example:
[16575.983359] sd 0:0:0:3: [sdd] Starting disk
[16575.983693] sd 0:0:0:3: [sdd] Start/Stop Unit failed: Result: hostbyte=0x00 driverbyte=DRIVER_OK
[16575.983712] sd 0:0:0:3: [sdd] Sense Key : 0x6
[16575.983730] sd 0:0:0:3: [sdd] ASC=0x29 ASCQ=0x0
[16575.983738] sd 0:0:0:3: PM: dpm_run_callback(): scsi_bus_resume+0x0/0xa0 returns -5
[16575.983783] sd 0:0:0:3: PM: failed to resume async: error -5
Make the SCSI core retry the START STOP UNIT command if the device reports
that it has been powered on or that it has been reset.
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240904210304.2947789-1-bvanassche@acm.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The header file linux/bio-integrity.h is included twice. Remove the last
one. The compilation test has passed.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240830075858.3541907-1-lihongbo22@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If formatting a suspended disk (such as formatting with different DIF
type), the disk will be resuming first, and then the format command will
submit to the disk through SG_IO ioctl.
When the disk is processing the format command, the system does not
submit other commands to the disk. Therefore, the system attempts to
suspend the disk again and sends the SYNCHRONIZE CACHE command. However,
the SYNCHRONIZE CACHE command will fail because the disk is in the
formatting process. This will cause the runtime_status of the disk to
error and it is difficult for user to recover it. Error info like:
[ 669.925325] sd 6:0:6:0: [sdg] Synchronizing SCSI cache
[ 670.202371] sd 6:0:6:0: [sdg] Synchronize Cache(10) failed: Result: hostbyte=0x00 driverbyte=DRIVER_OK
[ 670.216300] sd 6:0:6:0: [sdg] Sense Key : 0x2 [current]
[ 670.221860] sd 6:0:6:0: [sdg] ASC=0x4 ASCQ=0x4
To solve the issue, ignore the error and return success/0 when format is
in progress.
Cc: stable@vger.kernel.org
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Link: https://lore.kernel.org/r/20240819090934.2130592-1-liyihang9@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit f874d7210d88 ("scsi: sd: Keep the discard mode stable") attempted
to address an issue where one mode of discard operation got configured
prior to the device completing full discovery. Unfortunately this
change assumed discard was always enabled on the device.
Do not attempt to configure discard unless LBPME is enabled.
Link: https://lore.kernel.org/r/20240817005325.3319384-1-martin.petersen@oracle.com
Fixes: f874d7210d88 ("scsi: sd: Keep the discard mode stable")
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Flag REQ_ATOMIC can only be set for writes, so don't check if the operation
is also a write in sd_setup_read_write_cmnd().
Fixes: bf4ae8f2e640 ("scsi: sd: Atomic write support")
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240805113315.1048591-2-john.g.garry@oracle.com
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a scenario where a large number of discard commands are issued
when the iscsi initiator connects to the target and then performs a session
rescan operation. There is a time window, most of the commands are in UNMAP
mode, and some discard commands become WRITE SAME with UNMAP.
The discard mode has been negotiated during the SCSI probe. If the mode is
temporarily changed from UNMAP to WRITE SAME with UNMAP, an I/O ERROR may
occur because the target may not implement WRITE SAME with UNMAP. Keep the
discard mode stable to fix this issue.
Signed-off-by: Li Feng <fengli@smartx.com>
Link: https://lore.kernel.org/r/20240718080751.313102-2-fengli@smartx.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 804e498e0496 ("sd: convert to the atomic queue limits API")
introduced pairs of function calls to queue_limits_start_update() and
queue_limits_commit_update(). These two functions lock and unlock
q->limits_lock. In sd_revalidate_disk(), sd_read_cpr() is called after
queue_limits_start_update() call and before queue_limits_commit_update()
call. sd_read_cpr() locks q->sysfs_dir_lock and &q->sysfs_lock. Then new
lock dependencies were created between q->limits_lock, q->sysfs_dir_lock
and q->sysfs_lock, as follows:
sd_revalidate_disk
queue_limits_start_update
mutex_lock(&q->limits_lock)
sd_read_cpr
disk_set_independent_access_ranges
mutex_lock(&q->sysfs_dir_lock)
mutex_lock(&q->sysfs_lock)
mutex_unlock(&q->sysfs_lock)
mutex_unlock(&q->sysfs_dir_lock)
queue_limits_commit_update
mutex_unlock(&q->limits_lock)
However, the three locks already had reversed dependencies in other
places. Then the new dependencies triggered the lockdep WARN "possible
circular locking dependency detected" [1]. This WARN was observed by
running the blktests test case srp/002.
To avoid the WARN, move the sd_read_cpr() call in sd_revalidate_disk()
after the queue_limits_commit_update() call. In other words, move the
sd_read_cpr() call out of the q->limits_lock region.
[1] https://lore.kernel.org/linux-scsi/vlmv53ni3ltwxplig5qnw4xsl2h6ccxijfbqzekx76vxoim5a5@dekv7q3es3tx/
Fixes: 804e498e0496 ("sd: convert to the atomic queue limits API")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240801054234.540532-1-shinichiro.kawasaki@wdc.com
Tested-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull outstanding commits from 6.11 queue into fixes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 7a6bbc2829d4ab592c7e440a6f6f5deb3cd95db4.
The offending commit tried to suppress a double "Starting disk" message for
some drivers, but instead started spamming the log with bogus messages
every five seconds:
[ 311.798956] sd 0:0:0:0: [sda] Starting disk
[ 316.919103] sd 0:0:0:0: [sda] Starting disk
[ 322.040775] sd 0:0:0:0: [sda] Starting disk
[ 327.161140] sd 0:0:0:0: [sda] Starting disk
[ 332.281352] sd 0:0:0:0: [sda] Starting disk
[ 337.401878] sd 0:0:0:0: [sda] Starting disk
[ 342.521527] sd 0:0:0:0: [sda] Starting disk
[ 345.850401] sd 0:0:0:0: [sda] Starting disk
[ 350.967132] sd 0:0:0:0: [sda] Starting disk
[ 356.090454] sd 0:0:0:0: [sda] Starting disk
...
on machines that do not actually stop the disk on runtime suspend (e.g.
the Qualcomm sc8280xp CRD with UFS).
Let's just revert for now to address the regression.
Fixes: 7a6bbc2829d4 ("scsi: sd: Do not repeat the starting disk message")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240716161101.30692-1-johan+linaro@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
