| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next-2026-07-26
Mostly driver changes this time:
- new driver mm81x for an S1G device
- new driver nxpwifi for NXP devices
(mostly forked off from mwifiex)
- ath12k: much kernel infrastructure integration work
- brcmfmac: DPP support, some Cypress part update
- nl80211: per-link statistics support
====================
Link: https://patch.msgid.link/20260726105205.942922-60-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The spec says to include it if the STA is "capable of operating
as STA 6G", which is a bit unclear because this is defined at a
STA level and not at the MLD level or so, but WFA requires this
to be included. Either way, the element is completely advisory
and intended mostly for debugging (and perhaps a bit steering),
so just include it in association request all the time if 6 GHz
is supported.
To determine what exactly to include, check all the channels
that aren't disabled. That way, it ends up being a lowest
common denominator, which is most useful for steering etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260715210322.02a4f3fced21.I94bbd08ac38001e11d5143a8b3f54dcea8ae8e15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer.
Fixes: 09a740ce352e ("mac80211: receive and process S1G beacons")
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260611161943.91069-5-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Now that cfg80211 refuses all attempts to use 5/10 MHz
channels, all of this code is unreachable; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20260529084502.4e5a9350206c.I2f6169a067ddd1b5e234668fcb6e07957fafacf2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes, ieee80211_check_combinations fails, but it is hard to know
why exactly. We will have to return an array of reasons, one per
combination.
In cases where we want to check if it failed because there are not
enough chanctxs (and maybe remove one if needed), we can just not fill
in that chanctx(s) in iface_combination_params::num_different_channels
in ieee80211_fill_ifcomb_params, so that chanctx(s) won't be taken into
account.
To allow that, add an option to pass a callback to
ieee80211_fill_ifcomb_params. This callback will be called for each
chanctx we consider to count in num_different_channels and will return
whether or not this chanctx should be skipped and not counted.
This mechanism will be used later.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260527224745.0042232f996e.I5d323125e34f3b253510e85ceb7a770d59f689fb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case reconfiguration of NAN fails, we call
ieee80211_handle_reconfig_failure, that marks all interfaces as not in
the driver.
Then, at the error path of the reconfig, cfg80211_shutdown_all_interfaces
is called to destroy all the interfaces.
If we have any other interface but the NAN one, for example a BSS
station, then when its state (links, stations) will be removed, we
won't tell the driver about this, because we will think that the
interfaces are not in the driver, and then drivers might remain with
dangling pointers to objects like stations and links (at least for
iwlwifi this is the case).
ieee80211_handle_reconfig_failure is meant to be called after we cleaned
up the state in the driver, there is no reason to call it for NAN
reconfiguration failure.
Fix the code to just warn in such a case, as we do in other error paths
in reconfig where it is too complicated to rewind.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260513182548.6a25f3a0a6ec.I83d1f2a7eed20200a78a62757c6b193e3bab892b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-7.1-rc3).
Conflicts:
net/ipv4/igmp.c
726fa7da2d8c ("ipv4: igmp: get rid of IGMPV3_{QQIC,MRC} and simplify calculation")
c6bebaa744f7 ("ipv4: igmp: annotate data-races in igmp_heard_query()")
https://lore.kernel.org/a7365e4873340f7a5e30411207de3bf9@kernel.org
Adjacent changes:
net/psp/psp_main.c
30cb24f97d44 ("psp: strip variable-length PSP header in psp_dev_rcv()")
c2b22277ad89 ("psp: validate IPv4 header fields in psp_dev_rcv()")
net/sched/sch_fq_codel.c
f83e07b29246 ("net/sched: sch_fq_codel: annotate data-races from fq_codel_dump_class_stats()")
3f3aa77ff1c8 ("net/sched: add qstats_cpu_drop_inc() helper")
net/wireless/pmsr.c
0f3c0a197309 ("wifi: nl80211: fix NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST usage")
410aa47fd9d3 ("wifi: cfg80211: allow suppressing FTM result reporting for PD requests")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call to ieee80211_dfs_cac_cancel can cause the iterated chanctx to
be freed and removed from the list. Guard against this to avoid a
slab-use-after-free error.
Cc: stable@vger.kernel.org
Fixes: bca8bc0399ac ("wifi: mac80211: handle ieee80211_radar_detected() for MLO")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20260505151539.236d63a1b736.I35dbb9e96a2d4a480be208770fdd99ba3b817b79@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the device is capable, parse the AP chandef with NPCA.
Also advertise the other NPCA operational parameters to the
underlying driver and track if they change (though not with
BSS critical update etc. yet)
Since NPCA can only be enabled when the chanctx isn't shared,
the channel context code needs to clear/set npca.enabled in
the per-link configuration, except during association since
we can't enable NPCA before having completed association. In
this case, set npca.enabled during the association process.
Link: https://patch.msgid.link/20260428112708.eb1e42c0b6d7.I0acd8445d4600363afb8430922531450399d0fab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We can't use NPCA any more if the chandef was downgraded,
for obvious reasons. Clear NPCA during any downgrade.
Link: https://patch.msgid.link/20260428112708.2ab0e6f2e433.Ic39badb6782ef2242942424538f57e4a83391a06@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since 802.11bn D1.4 the DBE capabilities are after the
PHY capabilities, not between MAC and PHY, adjust the
code accordingly.
Also add a struct for DBE capabilities and use it for
checking the correct length instead of hard-coding the
lengths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260428103657.b40af50f182d.I75306a092dc2c8a9eb7276160f0b7144b4846d18@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a new wdev-only interface type NL80211_IFTYPE_PD to support
Proximity Detection (PD) operations such as PASN and peer measurement
operations. This interface type operates without a netdev, similar to
P2P_DEVICE and NAN interfaces.
Implement support across cfg80211 and mac80211 layers with PD-specific
checks gated by the NL80211_EXT_FEATURE_SECURE_RTT feature flag,
management frame registration and transmission capabilities, and proper
channel context handling where PD interfaces are excluded from bandwidth
calculations. Update mac80211 to recognize the new interface type in the
relevant paths for this management-only interface.
PD discovery can be performed on any available interface, such as
NL80211_IFTYPE_STATION.
If PD/PMSR uses the MAC address of an existing interface type, such as
NL80211_IFTYPE_STATION, then pairing and measurement shall use that
same interface. If PD/PMSR uses a different MAC address, such as a
random MAC address, then pairing and measurement can be performed on a
new NL80211_IFTYPE_PD interface created with that random MAC address.
Signed-off-by: Peddolla Harshavardhan Reddy <peddolla.reddy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260420090856.2152905-4-peddolla.reddy@oss.qualcomm.com
[fix comment style]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Just saying "Table 9-250" isn't useful, without the version
of the spec. Fix the number according to the latest released
version (-2020) and add the table name.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260415145157.c85df460fc98.I350b4c290fb90977f62ed59ac0246afbacee1ebc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This function is only called for at least HT capable stations,
so doesn't need to differentiate 20/20_NOHT. Also, the check
for VHT 160 MHz support is wrong, since a station could have
support for both and the AP is using 80+80, but nothing cares
anyway, so we don't need that.
Simplify the function and move it to util.c since it now no
longer is related to VHT, and also doesn't need a station.
Also use the new function in ieee80211_get_sta_bw() for the
chandef calculations, it just needs to handle the 20/20-noht
separately; while at it fix that to handle HE stations.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260415144514.7b0be1059436.I573add4e3ed68b15f8b45122d053ac523afe4025@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Peer schedules specify which channels the peer is available on and when.
Add support for configuring peer NAN schedules:
- build and store the schedule and maps
- for each channel, make sure that it fits into the capabilities, and
take the minimum between it and the local compatible nan channel.
- configure the driver
Note that the removal of a peer schedule should be done by the driver
upon NMI station removal.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.185ff2283fa6.I0345eb665be8ccf4a77eb1aca9a421eb8d2432e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for both NMI and NDI stations.
The NDI station will be linked to the NMI station of the NAN peer for
which the NDI station is added.
A peer can choose to reuse its NMI address as the NDI address.
Since different keys might be in use for NAN management and for data
frames, we will have 2 different stations, even if they'll have the same
address.
Even though there are no links in NAN, sta->deflink will still be used
to store the one set of capabilities and SMPS mode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.9fdd37b8e755.I7a7bd6e8e751cab49c329419485839afd209cfc6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make sure these interfaces are added to the driver only after the NAN
one was, and after NAN operation was started.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.b14392ce99d6.I2ba3bfcd93e47e48d7f7c74007c70cca52d46896@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A NAN local schedule consist of a list of NAN channels, and an array
that maps time slots to the channel it is scheduled to (or NULL to indicate
unscheduled).
A NAN channel is the configuration of a channel which is used for NAN
operations. It is a new type of chanctx user (before, the only user is a
link). A NAN channel may not have a chanctx assigned if it is ULWed out.
A NAN channel may or may not be scheduled (for example, user space
may want to prepare the resources before the actual schedule is
configured).
Add management of the NAN local schedule.
Since we introduce a new chanctx user, also adjust the different
for_each_chanctx_user_* macros to visit also the NAN channels and take
those into account.
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.03350fd40630.Id158f815cfc9b5ab1ebdb8ee608bda426e4d7474@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
NAN DE (Discovery Engine) may be handled in the device or in user space.
When handled in user space, all the NAN func management code should not
run. Moreover, devices with user space DE should not provide the
add/del_nan_func callbaks. For such devices, ieee80211_reconfig_nan will
always fail.
Make it clear what parts of ieee80211_if_nan are relevant to DE
management, and touch those only when DE is offloaded.
Add a check that makes sure that a driver doesn't register with
add_del/nan_func callbacks if DE is in user space.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.6665f64865cd.Iee24bef3bae2e1d502216192e760c1e699d271c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function is quite useful when handling beacon timestamps. Export it
so that it can be used by mac80211_hwsim and others.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.a1abc9c52f37.Ieabfe66768b1bf64c3076d62e73c50794faeacdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently there is no TXQ for non-data frames. Add a new txq_mgmt for
this purpose and create one of these on NAN devices. On NAN devices,
these frames may only be transmitted during the discovery window and it
is therefore helpful to schedule them using a queue.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.32eddd986bd2.Iee95758287c276155fbd7779d3f263339308e083@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This new interface type represents a NAN data interface (NDI).
It is used for data communication with NAN peers.
Note that the existing NL80211_IFTYPE_NAN interface, which is the NAN
Management Interface (NMI), is used for management communication.
An NDI interface is started when a new NAN data path is about to
be established, and is stopped after the NAN data path is terminated.
- An NDI interface can only be started if the NMI is running, and NAN is
started.
- Before the NMI is stopped, the NDI interfaces will be stopped.
Add the new interface type, handle add/remove operations for it,
and makes sure of the conditions above.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.0d681335c2e2.I92973483e927820ae2297853c141842fdb262747@changeid
Link: https://patch.msgid.link/20260318123926.206536-4-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The action code actually serves to identify the type of action
frame, so it really isn't part of the per-type structure. Pull
it out and have it in the general action frame format.
In theory, whether or not the action code is present in this
way is up to each category, but all categories that are defined
right now all have that value.
While at it, and since this change requires changing all users,
remove the 'u' and make it an anonymous union in this case, so
that all code using this changes.
Change IEEE80211_MIN_ACTION_SIZE to take an argument which says
how much of the frame is needed, e.g. category, action_code or
the specific frame type that's defined in the union. Again this
also ensures that all code is updated.
In some cases, fix bugs where the SKB length was checked after
having accessed beyond the checked length, in particular in FTM
code, e.g. ieee80211_is_ftm().
Link: https://patch.msgid.link/20260226183607.67e71846b59e.I9a24328e3ffcaae179466a935f1c3345029f9961@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Add support for making UHR connections and accepting AP
stations with UHR support.
Link: https://patch.msgid.link/20260130164259.7185980484eb.Ieec940b58dbf8115dab7e1e24cb5513f52c8cb2f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Prior initiating communication in a DFS channel, there should be a
monitoring of RADAR in that channel for a minimum of 600 seconds if it
is a Weather RADAR channel and 60 seconds for other DFS channels. This
Channel Availability Check(CAC) is currently implemented by scheduling
a work item for execution with a delay equal to an appropriate timeout.
But this work item is observed to take more delay than specified
(4-5 seconds in regular DFS channels and 25-30 seconds in Weather RADAR
channels). Even though this delay is expected in case of delayed work
queue as there is no guarantee that the work will be scheduled exactly
after the specified delay, a delay of more than 20 seconds is too much
for the AP to be in non-operational state.
Recently commit 7ceba45a6658 ("wifi: cfg80211: add an hrtimer based
delayed work item") added an infrastructure to overcome this issue by
supporting high resolution timers for mac80211 delayed work, which do not
have this timeout latency. Switch the CAC timeout to use this
infrastructure, so the CAC completion handling is triggered with tighter
timing and reduced latency.
Signed-off-by: Amith A <amith.a@oss.qualcomm.com>
Link: https://patch.msgid.link/20260130035511.2328713-1-amith.a@oss.qualcomm.com
[fix delay handling]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, in MLO connections, userspace constructs most of the
Authentication frame body, excluding the Multi-Link element (MLE),
which mac80211 appends later in ieee80211_send_auth(). At present,
mac80211 always adds the MLE itself, since userspace
(e.g. wpa_supplicant) does not yet include it.
However, for new authentication protocols such as Enhanced Privacy
Protection Key Exchange (EPPKE), as specified in
"IEEE P802.11bi/D3.0 section 12.16.9", the MLE must be included in
userspace so that the Message Integrity Code (MIC) can be computed
correctly over the complete frame body. Table 9-71 specifies that
the MIC is mandatory. If mac80211 appends the MLE again, the
Authentication frame becomes invalid.
Add a check in ieee80211_send_auth() to detect whether the MLE is
already present in the Authentication frame body before appending.
Skip the append if the MLE exists, otherwise add it as before.
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-7-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Right now, the only way to iterate stations is to declare an
iterator function, possibly data structure to use, and pass all
that to the iteration helper function. This is annoying, and
there's really no inherent need for it.
Add a new for_each_station() macro that does the iteration in
a more ergonomic way. To avoid even more exported functions, do
the old ieee80211_iterate_stations_mtx() as an inline using the
new way, which may also let the compiler optimise it a bit more,
e.g. via inlining the iterator function.
Link: https://patch.msgid.link/20260108143431.d2b641f6f6af.I4470024f7404446052564b15bcf8b3f1ada33655@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Right now, the only way to iterate interfaces is to declare an
iterator function, possibly data structure to use, and pass all
that to the iteration helper function. This is annoying, and
there's really no inherent need for it, except it was easier to
implement with the iflist mutex, but that's not used much now.
Add a new for_each_interface() macro that does the iteration in
a more ergonomic way. To avoid even more exported functions, do
the old ieee80211_iterate_active_interfaces_mtx() as an inline
using the new way, which may also let the compiler optimise it
a bit more, e.g. via inlining the iterator function.
Also provide for_each_active_interface() for the common case of
just iterating active interfaces.
Link: https://patch.msgid.link/20260108143431.f2581e0c381a.Ie387227504c975c109c125b3c57f0bb3fdab2835@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is only used within mac80211, and not even declared in
a public header file. Don't export it.
Link: https://patch.msgid.link/20260109095029.2b4d2fe53fc9.I9f5fa5c84cd42f749be0b87cc61dac8631c4c6d0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For monitoring, userspace will try to configure the VIF sdata, while the
driver may see the monitor_sdata that is created when only monitor
interfaces are up. This causes the odd situation that it may not be
possible to store the MU-MIMO configuration on monitor_sdata.
Fix this by storing that information on the VIF sdata and updating the
monitor_sdata when available and the interface is up. Also, adjust the
code that adds monitor_sdata so that it will configure MU-MIMO based on
the newly added interface or one of the existing ones.
This should give a mostly consistent behaviour when configuring MU-MIMO
on sniffer interfaces. Should the user configure MU-MIMO on multiple
sniffer interfaces, then mac80211 will simply select one of the
configurations. This behaviour should be good enough and avoids breaking
user expectations in the common scenarios.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110141514.677915f8f6bb.If4e04a57052f9ca763562a67248b06fd80d0c2c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ieee80211_recalc_chanctx_min_def() is used outside the chandef
code, but then should/is always used with NULL/false for the
two last arguments. Remove them, and create another level of
indirection for use inside the file.
Link: https://patch.msgid.link/20251105160431.33408844c392.I4f52298861780c17a27cd229609e8a3e29c8d740@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Each link can currently use a chanctx and have another one
reserved, and both of these are also tracked backwards in
the assigned_links and reserved_links lists. If we consider
that there aren't *that* many links, this duplicate book-
keeping isn't necessary.
(I think it used to be necessary before the wiphy locking
changes, when chanctx_mtx existed, because we couldn't do
any interface iterations while holding only chanctx_mtx.)
Additionally, for NAN, we're going to want to track which
chanctxs are in use by the (group of) NAN interfaces. For
those, links don't really make sense as such, so chanctxs
need to be assigned to a different data structure.
Thus, as a first step, remove those back-lists of users
(right now only links) of each channel context. This is a
very basic conversion, ieee80211_vif_use_reserved_switch()
should made to iterate smarter.
Link: https://patch.msgid.link/20251105160431.dbeea1c42e76.I8d273c407274e1c05a4778aa20b56a9f326e87a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When moving to the APs channel, ensure we correctly initialise the chandef
and perform the required validation. Additionally, if the AP is beaconing on a
2MHz primary, calculate the 2MHz primary center frequency by extracting
the sibling 1MHz primary and averaging the frequencies to find the 2MHz
primary center frequency.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250918051913.500781-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
So it can be used by drivers to check if NAN Device interface
is started or not.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.c69652f77eb6.Ie4f3d197e0706e742e3d97614fadc11b22adfbc6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is only needed within the 'if' scope, not in the function scope.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250903083904.1972284-3-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_get_radio_idx_by_chan()
In several instances where cfg80211_get_radio_idx_by_chan() is called,
redundant checks are performed across function — such as verifying if
wiphy->n_radio < 2 or if the returned index is negative. These checks are
unnecessary, as the return value can be directly compared. Moreover, the
function can be safely called even when radio-level properties are not
explicitly advertised since in such case in each call it is going to get
same error value.
Therefore, simplify the usage of this function across all such cases by
removing redundant conditions and relying on the return value directly.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812-fix_scan_ap_flag_requirement_during_mlo-v4-2-383ffb6da213@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce the sb_count variable which tracks the number of
beacon intervals until the next long beacon. To initialise this
value, we find the current short beacon index into this period
which represents the number of short beacons left to send before
the next long beacon. We use the same TSF value used to initialise
the DTIM count to ensure the short beacon count and DTIM count
are in sync as its common for the long beacon period and DTIM period
to be equivalent.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-4-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc6-2).
No conflicts.
Adjacent changes:
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
c701574c5412 ("wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan")
b3a431fe2e39 ("wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan()")
drivers/net/wireless/mediatek/mt76/mt7996/mac.c
62da647a2b20 ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
dc66a129adf1 ("wifi: mt76: add a wrapper for wcid access with validation")
drivers/net/wireless/mediatek/mt76/mt7996/main.c
3dd6f67c669c ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()")
8989d8e90f5f ("wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()")
net/mac80211/cfg.c
58fcb1b4287c ("wifi: mac80211: reject VHT opmode for unsupported channel widths")
037dc18ac3fb ("wifi: mac80211: add support for storing station S1G capabilities")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In reconfig we add the virtual monitor in 2 cases:
1. If we are resuming (it was deleted on suspend)
2. If it was added after an error but before the reconfig
(due to the last non-monitor interface removal).
In the second case, the removal of the non-monitor interface will succeed
but the addition of the virtual monitor will fail, so we add it in the
reconfig.
The problem is that we mislead the driver to think that this is an existing
interface that is getting re-added - while it is actually a completely new
interface from the drivers' point of view.
Some drivers act differently when a interface is re-added. For example, it
might not initialize things because they were already initialized.
Such drivers will - in this case - be left with a partialy initialized vif.
To fix it, add the virtual monitor after reconfig_complete, so the
driver will know that this is a completely new interface.
Fixes: 3c3e21e7443b ("mac80211: destroy virtual monitor interface across suspend")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233451.648d39b041e8.I2e37b68375278987e303d6c00cc5f3d8334d2f96@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement dot11ExtendedRegInfoSupport to advertise non-AP station
regulatory power capability as part of regulatory connectivity
element in (Re)Association request frames so that AP can achieve
maximum client connectivity. Control field which was interpreted
using value of 3-bits B5 to B3, now uses value of 4-bits B6 to B3 to
interpret the type of AP. Hence update IEEE80211_HE_6GHZ_OPER_CTRL_REG_INFO
to parse 4-bits control field. If older AP still updates only 3-bits
value of control field, station can still interpret the value as per
section E.2.7 of IEEE 802.11 REVme D7.0 and support the appropriate
AP type.
Also update IEEE80211_6GHZ_CTRL_REG_INDOOR_SP_AP as the value of
standard power AP is changed to 8 instead of 4 so that AP can support both
LPI AP and SP AP to maximize the connectivity with stations. For backward
compatibility, keeping value 4 as old AP by limiting it to SP AP only.
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609213232.90cdef116aad.I85da390fbee59355e3855691933e6a5e55c47ac4@changeid
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc4).
Conflicts:
Documentation/netlink/specs/mptcp_pm.yaml
9e6dd4c256d0 ("netlink: specs: mptcp: replace underscores with dashes in names")
ec362192aa9e ("netlink: specs: fix up indentation errors")
https://lore.kernel.org/20250626122205.389c2cd4@canb.auug.org.au
Adjacent changes:
Documentation/netlink/specs/fou.yaml
791a9ed0a40d ("netlink: specs: fou: replace underscores with dashes in names")
880d43ca9aa4 ("netlink: specs: clean up spaces in brackets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to get the radio for which RTS threshold needs to be changed
from userspace. Pass on this radio index to underlying drivers as an
additional argument.
A value of -1 indicates radio index is not mentioned and that the
configuration applies to all radio(s) of the wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-5-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, in supporting API's to fill sinfo structure from sta
structure, is mapped to fill the fields from sta->deflink. However,
for multi-link (ML) station, sinfo structure should be filled from
corresponding link_id.
Therefore, add link_id as an additional argument in supporting API's
for filling sinfo structure correctly. Link_id is set to -1 for non-ML
station and corresponding link_id for ML stations. In supporting API's
for filling sinfo structure, check for link_id, if link_id < 0, fill
the sinfo structure from sta->deflink, otherwise fill from
sta->link[link_id].
Current, changes are done at the deflink level i.e, pass -1 as link_id.
Actual link_id will be added in subsequent patches to support
station statistics for MLO.
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Link: https://patch.msgid.link/20250528054420.3050133-2-quic_sarishar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As we are converting from TU to usecs, a beacon interval of
100*1024 usecs will lead to integer wrapping. To fix change
to use a u32.
Fixes: 057d5f4ba1e4 ("mac80211: sync dtim_count to TSF")
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250621123209.511796-1-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, in multi-radio wiphy cases, if a scan is ongoing on one radio,
-EBUSY is returned when DFS or a channel switch is initiated on another
radio. Because of this, an MLD AP with one radio (link) in an ongoing scan
cannot initiate DFS or a channel switch on another radio (link).
In multi-radio wiphy cases, multiple radios are grouped under a single
wiphy. Hence, if a scan is ongoing on one underlying radio and DFS or a
channel switch is requested on a different underlying radio of the same
wiphy, these operations can be allowed simultaneously.
Add logic to check the underlying radio used for the ongoing scan. If the
radio on which DFS or a channel switch is requested is not being used for
the scan, allow the operation; otherwise, return -EBUSY.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250527-mlo-dfs-acs-v2-2-92c2f37c81d9@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We still have ieee80211_chandef_rate_flags() and all that,
but all the users seem pretty much broken (deflink, etc.)
Remove all the code. It's been two years since last anyone
even vaguely entertained the notion of looking at this and
fixing it.
Link: https://patch.msgid.link/20250329221419.c31da7ae8c84.I1a3a4b6008134d66ca75a5bdfc004f4594da8145@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff89 ("selftests: drv-net: add xdp cases for ping.py")
de94e8697405 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0fa0 ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b9b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175ccad4 ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f913 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552eda ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d38e ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
